Hach DR 6000 User Manual Download Page 120

Page: 120 / 156

120

Expanded programs

Place the analysis cell in the cell compartment.

Close the cell compartment cover.

Press

Read

10.

Remove the analysis cell.

11.

Close the cell compartment cover.

12.

Press

Zero

13.

Place the analysis cell in the cell compartment.

14.

Close the cell compartment cover.

15.

Press

Read

16.

Repeat this procedure until 5 comparison measurements
have been obtained.

The result will be displayed.

17.

Compare the result with the analysis cell required values.

18.

Press

Cancel

to return to Optical Checks.

6.7.3.5

Noise Check

With the noise check the photometric noise in the device is
checked.

This test can be used to test the noise at any wavelength during
use of a sample that corresponds to the absorbance level of this
wavelength.

Press

Noise Check

in the "Optical Checks" menu.

Press



to select the wavelength.

Enter the wavelength and press

to confirm your

selection.

Summary of Contents for DR 6000




























































































































































Search results

Summary of Contents for DR 6000

Reviews:

Brands by name

Popular brands

Hach DR 6000, User Manual

Search results

Summary of Contents for DR 6000

Reviews:

Brands by name

Popular brands