Hach DR 6000 User Manual Download Page 117

Page: 117 / 156

117

Expanded programs

When results exceed allowable tolerances (given in the quality
control certificate to the test record), contact the manufacturer.

Press

Verification Kit

in the "Optical Checks" menu.

Press

Nominal Values

Press

Edit

An automatic menu guidance queries values (filters,
wavelength, nominal values and tolerances) given in the
quality control certificate, to the following specifications:

•

Stray light

•

Photometrical accuracy

•

Wavelength accuracy

Press

when all values are entered and the overview is

displayed.

Press

Verification

Insert the universal cell adapter(

Figure 3, Page 21

) into the

cell compartment (2).

Remove any cells from the cell compartment.

Close the cell compartment cover.

Press

Start

Summary of Contents for DR 6000




























































































































































Search results

Summary of Contents for DR 6000

Reviews:

Brands by name

Popular brands

Hach DR 6000, User Manual

Search results

Summary of Contents for DR 6000

Reviews:

Brands by name

Popular brands