ENGINE ELECTRICAL 6D-9
laminated core that forms part of the generator frame. A
recitifier bridge connected to the stator windings contains
six diodes, and electrically changes the stator a.c. voltages to
a d.c. voltage which appears at the generator output
terminal. Generator field current is supplied through a diode
trio which also is connected to the stator windings. A
capacitor or condenser, mounted in the end frame protects
the rectifier bridge and diode trio from high voltages, and
suppresses radio noise.
No periodic adjustments or maintenance of any kind
are required on the entire generator assembly.
N O IS Y G E N E R A T O R
Noise from a generator may be caused by a loose drive
pulley, loose mounting bolts, worn or dirty bearings,
defective diode, or defective stator.
DIAGNOSIS
Most charging system troubles show up as a faulty
indicator lamp, an undercharged or an overcharged battery.
Since the battery itself may be defective, it should be
checked first to determine its condition. Also, in the case of
an undercharged battery, check for battery drain caused by
grounds or by accessories being left on.
A basic wiring diagram showing lead connections is
shown in Figure 6D-3C. To avoid damage to the electrical
equipment, always observe the following precautions:
• Do not reverse connections to the generator.
• Do not short across or ground any of the terminals in
the charging circuit except as directed by the
instructions.
• NEVER operate the generator with the output
terminal disconnected.
• When connecting a charger or a booster battery to the
vehicle battery, see Battery Charging Section.
In some vehicles, a voltmeter may be used instead of an
indicator lamp. In this case, Section "A" pertaining to
faulty indicator lamp operation should be omitted from the
troubleshooting procedure.
Trouble in the charging system will show up as one or
more of the following conditions:
A. Faulty indicator lamp operation.
B. Choke light stays on after engine is running (Gage
Cars).
C. An undercharged battery as evidenced by slow
cranking or hydrometer dark.
D. An overcharged battery as evidenced by excessive
spewing of electrolyte from the vents.
A.
FAULTY INDICATOR LAMP OPERATION.
Check the indicator lamp for normal operation as
shown in Fig. 6D-4C.
If the indicator lamp operates normally, proceed to
"Undercharged Battery" section. Otherwise, proceed to
one of the following three abnormal conditions.
1. Switch Off, Lamp On--Unplug the connector from the
generator No. 1 and No. 2 terminals. If the lamp stays
on, there is a short between these two leads. If the lamp
goes out, replace the rectifier bridge as covered in the
"GENERATOR REPAIR" Section. This condition
will cause an undercharged battery.
2. Switch On, Lamp Off, Engine Stopped-This condition
can be caused by the defects listed in part
1
above, or by
an open in the circuit. To determine where an open
exists, proceed as follows:
a. Check for a blown fuse, or a burned out bulb,
defective bulb socket, or an open in No. 1 lead circuit
between generator and ignition switch.
b. If no defects have been found, proceed to
Undercharged Battery section.
3. Switch On, Lamp On, Engine Running - Check for a
blown fuse (where used) between indicator lamp and
switch, and also in A/C circuit. The other possible
causes of this condition are covered
in the
"UNDERCH ARG ED BATTERY" section. If a
defect has been found and corrected at this point, no
further checks need be made.
B. CHOKE LIGHT ON AFTER START.
If the generator fails to produce from 12 to 14.5 volts
after the engine is running, the choke heater relay will be
grounded through the brown white wire to the generator at
terminal 1. This will cause the relay points to remain open,
thus stopping current flow back through the choke heater
relay. This will cause the choke indicator to light.
1
. Check generator terminal
1
for voltage during fast idle.
If voltage is incorrect, see On-Car Service and Unit
Repair.
U N D E R C H A R G E D BATTERY
This condition, as shown by slow cranking or
hydrometer dark can be caused by one or more of the
following conditions even though the indicator lamp may be
operating normally. This procedures also applies to vehicles
with a voltmeter.
1. Insure that the undercharged condition has not been
caused by accessories having been left on for extended
periods.
2. Check the drive belt for proper tension (see Section
6
B).
3. If a battery defect is suspected, refer to Battery
Section.
4. Inspect the wiring for defects. Check all connections for
tightness and cleanliness, including the slip connectors
at the generator and cowl and the battery cable
connections at the battery, the starter and the engine
ground.
5. With ignition switch "on" and all wiring harness leads
connected, connect a voltmeter from:
a. Generator "BAT" terminal to ground.
b. Generator No. 1 terminal to ground.
c. Generator No. 2 terminal to ground.
A zero reading indicates an open between voltmeter
connection and battery.
Generators have a built-in feature which avoids
overcharge and accessory damage by preventing the
generator from turning on if there is an open in the wiring
harness connected to the No. 2 (sensing) generator terminal.
6
. If previous Steps 1 through 5 check satisfactorily,
check generator as follows:
a. Disconnect battery ground cable.
b. Connect an ammeter or generator tester in the
circuit at the " BAT " terminal of the generator.
c. Reconnect negative battery cable.
Summary of Contents for 1982 Light Duty Truck
