![background image](http://html1.mh-extra.com/html/gmc/1982-light-duty-truck/1982-light-duty-truck_service-manual_2235920557.webp)
BRAKES
5-37
Reassembly
1. Lubricate the bore in the caliper and the new piston
seal with clean brake fluid. Position the seal in the
caliper bore groove. Lubricate the piston with clean
brake fluid and assemble a new boot into the groove in
the piston so that the fold faces the open end of the
piston. Insert the piston into the caliper bore, using care
not to unseat the seal and force down to the bottom in
the bore. This will require a force of 50 to 100 pounds
(220 to 440 N). Position the outside diameter of the
boot in the caliper counterbore and seat with Tool
J-22904 (fig. 5-38).
2. Check the boot installation to make sure that the
retaining ring molded into the boot is not bent and that
the boot is installed fully, below the caliper face, and
evenly all around. Otherwise dirt or moisture may enter
the bore and cause damage or corrosion.
3. Install the brake hose in the caliper inlet using a new
copper gasket.
Installation
1. Installation of the caliper and mounting parts (rubber
bushing, sleeves, shoe and lining assemblies and pins) is
the same as for lining replacement except for the
following:
a. The brake hose must be connected to the brake pipe
at the frame or frame bracket.
Use extreme care to orient the hose so that the keyed
hose end fitting aligns with the slot in the bracket
without twisting or kinking the hose.
b. After overhaul -- or any time that the brake hose or
line is disconnected - the calipers must be bled.
Bendix
Removal
Clean dirt from hose to caliper connection before
proceeding with removal.
1. Remove the hose to caliper bolt and cap or tape the
open connections to prevent dirt from entering the hose
or caliper. Discard the copper gaskets.
2. Remove the caliper assembly as described under "Shoe
and Linings-Removal".
Disassembly (Fig. 5-39)
1. Clean the exterior of the caliper using clean brake fluid
and place on a clean work surface.
2. Drain the brake fluid from the caliper.
CAUTION: Do not place the fingers in front of the
piston in an attem p t to catch or protect it w hen
applying compressed air.
3. Using clean shop cloths, pad the interior of the caliper
and remove the piston by directing compressed air into
the caliper inlet hole (fig. 5-40).
NOTICE:
Use just enough air pressure to ease the piston
out of the bore. Do not blow piston out of the bore as
damage to the piston could result. If the piston is seized
or cocked or does not come out readily, release the air
pressure and use a soft (brass) hammer to rap sharply
on and around the end of the piston. Reapply air
pressure to remove the piston.
An alternate method of removing the piston is to stroke
the brake pedal (gently) while the hydraulic lines are
still connected. This will push the piston out of the
caliper bore.
4. Remove the boot from the piston bore.
5. Using a small piece of wood or plastic, remove the
square ring seal from the piston bore.
NOTICE:
Do not use a metal tool of any kind for this
operation as it may damage the bore.
6. Remove the bleeder valve from the caliper.
Cleaning and Inspection
The dust boot and piston seal are to be replaced
whenever the caliper is overhauled. Discard these parts.
1. Clean all parts (other than those mentioned above in
clean brake fluid. Use dry, filtered, compressor air to
blow out all passages in the caliper and bleeder valve.
NOTICE:
The use of lubricated shop air will leave a film
of mineral oil on the metal parts. This may damage
Summary of Contents for 1982 Light Duty Truck
