BRAKES
5-59
NORMAL
LANCE
DEEP
LANCE
NORMAL
LANCE
Fig. 5-3B--Lances in Rear Housing L
bench with the front plate down. Unscrew the rear
plate completely and carefully lift it off the front plate
hub, grasping the air valve plunger and valve return
spring as the parts are separated (fig. 5-5B).
25. Remove the square ring seal from the shoulder of the
front diaphragm plate hub.
26. Remove the reaction disc from inside the front
diaphragm plate hub. Carefully slide the center plate
off the hub of the front plate.
27. Remove the diaphragms from the plates.
28. Use a blunt punch or 1-1/4" socket to drive seal from
rear housing (figs. 5-6B and 5-7B).
Cleaning
All parts to be reused should be washed in denatured
alcohol or brake fluid. Dry the parts with compressed air and
place them on clean paper or lint free cloth.
Small rust spots inside the shells may be removed with
crocus cloth or fine emery cloth. Be sure to clean thoroughly
after using any abrasive.
Inspect all parts and replace any that are damaged or
show excessive wear.
Assem bly
1. Press the new bearing and seal into the cavity in the
rear housing using Tool J-22677 (fig. 5-8B). The flat
rubber surface of the seal should be 5/16" below the
flat, inside surface of the rear housing.
2. Install reaction disc in hub of front plate with small tip
toward hole. Use rounded rod to seat disc.
3. Mount Tool J-22839 in vise.
4. Install front diaphragm on front plate. Long fold of
diaphragm must be facing down.
5. Install Tool J-22733 over threads on front plate hub
(fig. 5-9B).
6. Apply a light film of silicone lubricant to front plate
hub and to seal in center plate, then guide center plate,
seal first, onto the front plate hub, being careful not to
damage center plate seal. Remove Seal Protector
J-22733.
7. Apply a light coat of silicone lubricant to bearing
surfaces of air valve plunger, being careful not to apply
lubricant to rubber grommet inside plunger. Install
square ring seal on shoulder of front plate hub and
install valve plunger return spring and plunger in base
of front plate hub (fig. 5-1 OB).
8. Set rear plate over hub of front plate, and using hands
only, screw plate on hub, making sure that valve and
spring are properly aligned. Hand torque plates to 150
in. lbs. Check travel of valve plunger with index finger.
9. Assemble rear diaphragm to rear plate and place lip of
diaphragm in groove in rear plate. Install diaphragm
retainer over rear diaphragm and lip of center plate.
Using fingers, press retainer until it seats on shoulder of
center plate (fig. 5-11B).
10. Apply talcum powder to inside wall of rear housing and
silicone lubricant to the scalloped cutouts of front
housing and to seal in rear housing. Assemble
diaphragm and plate assembly into rear housing by
carefully guiding rear plate hub through seal in rear
housing. Bosses on center plate must be aligned
between lances in rear housing for reassembly. Work
outer rim of front diaphragm into rear housing with
screwdriver blade so that it is under lances in housing.
11. Attach base of Holding Fixture J-22805 to front
housing with nuts and washers and draw down tight to
eliminate bending or damage to studs.
12. Secure front housing and Holding Fixture J-22805 on
arbor press plate by a suitable means (fig. 5-4B).
13. Place Spanner Wrench J-9504 over studs on rear
J-9504
Fig. 5-4B~Holding and Separating Housings Using J-22805 and
J-9504 in Arbor Press
Summary of Contents for 1982 Light Duty Truck
