IN-LINE 6
6A1-17
3. Install seal to front cover, pressing tips into holes
provided in cover.
On LE3 engine, place a 3/16 " (5mm) diameter bead of
RTV on cover sealing surface.
4. Coat the gasket with gasket sealer and place in position
on cover.
5. Apply a 1/8" (3mm) bead of RTV sealant, # 1052366
or equivalent, to the joint formed at the oil pan and
cylinder block.
6
. Install centering Tool J-23042 in crankcase front cover
seal.
NOTICE:
It is important that centering tool be used to
align crankcase front cover so that torsional damper
installation will not damage seal and so that seal is
positioned evenly around damper hub.
7. Install crankcase front cover to block. Install and
partially tighten the two, oil pan-to-front cover screws.
8
. Install the front cover-to-block attaching screws.
9. Remove centering Tool J-23042 and torque all cover
attaching screws to 80 lb. in. (9N-m).
1
0. Install torsional damper as outlined.
OIL SEAL (FRONT CO VER)
Replacement
With Cover Installed
1. With torsional damper removed, pry old seal out of
cover from the front with a large screw driver, being
careful not to damage the seal surface on the cover.
2. Install new seal so that open end of seal is toward the
inside of cover and drive it into position with Tool
J-23042.
With Cover Removed
1. With cover removed, pry old seal out of cover from the
front with screw driver, being careful not to distort
cover.
2. Install new seal so that open end of the seal is toward
the inside of cover and drive it into position with Tool
J-23042.
C A M S H A F T
Measuring Lobe Lift
1. Remove valve mechanism as previously outlined.
2. Position indicator with ball socket adapter (Tool
J-8520) on push rod (fig. 6A1-23).
3. Rotate the cranksahft slowly in the direction of rotation
until the lifter is on the heel of the cam lobe. At this
point, the push rod will be in its lowest position.
4. Set dial indicator on zero, then rotate the crankshaft
slowly, or attach an auxiliary starter switch and
"bump" the engine over, until the push rod is in the
fully raised position. Disconnect the coil primary lead
before cranking.
5. Compare the total lift recorded from the dial indicator
with specifications.
6
. Continue to rotate the crankshaft until the indicator
reads zero. This will be a check on the accuracy of the
original indicator reading.
Removal
1. Remove engine following procedure in this section.
2. Remove lifters as previously outlined.
3. Remove crankcase front cover as previously outlined.
4. Remove fuel pump.
5. Align timing gear marks then remove the two camshaft
thrust plate bolts by working through holes in camshaft
gear.
6
. Remove the camshaft and gear assembly by pulling it
out through the front of the block. Support camshaft
carefully when removing so as not to damage the
camshaft bearings.
Inspection
The camshaft bearing journals should be measured
with a micrometer for an out-of-round condition. If the
journals exceed
.001
" out-of-round, the camshaft should be
replaced.
Inspect the camshaft gear and thrust plate for wear or
damage. Measure the camshaft end play. This should be
.
0 0 1
" to .005".
Gear Replacement
1. If the inspection indicated that the camshaft, gear or
thrust plate should be replaced, the gear must be
removed from the camshaft. This operation requires
the use of camshaft gear remover J-971.
2. Place the camshaft through the gear remover, place
end of remover on table of a press and press shaft out of
gear.
NOTICE:
Thrust plate must be positioned so that
woodruff key in shaft does not damage it when the shaft
Fig. 6Al-23--Measuring Camshaft Lobe Lift
7. If camshaft readings for all lobes are within specifica
tions, remove dial indicator assembly.
8
. Install and adjust valve mechanism as outlined.
Summary of Contents for 1982 Light Duty Truck
