BRAKES
5-43
ORIGINAL
DRUM DIAMETERS
MAXIMUM REFINISH
REPLACEMENT
(DISCARD)
11.000
11.060
11.090
11.150
11.210
11.240
12.000
12.060
12.090
13.000
13.060
13.090
inserting cable in channel of lever. Release spring.
6. Install primary shoe (short lining) to lever as follows:
Place pin in lever, place washer on pin and push pin
through hole in primary shoe. Fasten parts together by
installing the clip in groove of pin.
7. Fasten two brake shoes and linings together by
installing connecting spring. Move the shoes toward
each other and install adjusting screw.
8. Lubricate the flange plate contact surfaces with a very
light coat of Delco Brake Lube (or equivalent).
9. Place shoe and linings in position on flange plate.
When facing the brake assembly, the shoe with the
short lining should be to the left with the lever
assembled to it (automatic transmission), to the right
(manual transmission).
10. Pull brake shoes apart and install strut lever and spring
between them. The loop on the strut spring should be in
the "up" position.
11. Install hold down pins, washers, springs and cups from
flange plate to shoes.
12. Place guide plate on anchor pin.
13. Install pull back springs.
14. Remove the " knock out" plug (if necessary) and install
a new metal plug in the brake drum adjusting hole.
15. Install the brake drum.
16. Install the propeller shaft.
BRAKE DRUMS
Inspection and Reconditioning
NOTICE:
See "Notice" on Page 1 of this section.
Whenever brake drums are removed, they should be
thoroughly cleaned and inspected for cracks, scores, deep
grooves and out-of-round.
A cracked drum is unsafe for further service and must
be replaced. Do not attempt to weld a cracked drum.
Smooth up any slight scores. Heavy or extensive
scoring will cause excessive brake lining wear, and it will
probably be necessary to rebore in order to true up the
braking surface.
If the brake linings are slightly worn and the drum is
grooved, the drum should be polished with fine emery cloth
but should not be turned. At this stage, eliminating the
grooves in drum would necessitate removal of too much
metal, while if left alone, the grooves and lining ridges
match and satisfactory service can be obtained.
If brake linings are to be replaced, a grooved drum
should be turned for use with new linings. A grooved drum,
if used with new lining, will not only wear the lining, but will
make it difficult, if not impossible to obtain efficient brake
performance.
An out-of-round drum makes accurate brake shoe
adjustment impossible and is likely to cause excessive wear
of other parts of brake mechanism due to its eccentric
action. An out-of-round drum can also cause severe and
irregular tire tread wear as well as pulsating brake pedal.
When the braking surface of a brake drum exceeds the
factory specification limits in taper (and/or) being out-of-
round, the drum should be turned to true up the braking
surface. Out-of-round as well as taper and wear can be
accurately measured with an inside micrometer fitted with
proper extension rods.
When measuring a drum for out-of-round, taper and
wear, take measurements at the open and closed edges of
machined surface and at right angles to each other.
Turning Brake Drums
If a drum is to be turned, only enough metal should be
removed to obtain a true, smooth braking surface. If a drum
does not clean-up when turned to a maximum diameter as
shown in the general specification, it must be replaced.
Removal of more metal will affect dissipation of heat and
may cause distortion of the drum.
All brake drums have a maximum diameter cast into
them. This diameter is the maximum wear diameter and not a
refinish diameter. Do not refinish a brake drum that will not
meet the specifications, as shown below, after refinishing.
Brake Drum Balance
During manufacture, brake drums are balanced. Any
balance weights must not be removed.
WHEEL CYLINDER
Removal
1. Remove wheel, drum and brake shoes. Be careful not to
get grease or dirt on brake lining.
2. Remove wheel cylinder from backing plate.
Disassembly
1. Inspect cylinder bore for scoring or corrosion. It is best
to replace a corroded cylinder.
2. Polish any discolored or stained area with crocus cloth
by revolving cylinder on cloth supported by a finger.
3. Rinse cylinder in clean brake fluid.
4. Shake excessive rinsing fluid from cylinder. Do not use
a rag to dry cylinder, as lint from the rag cannot be kept
from cylinder bore surfaces.
Assembly
1. Lubricate cylinder bore and counterbore with clean
brake fluid and insert spring-expander assembly.
2. Install new cups. (Be sure cups are lint and dirt free.)
Do not lubricate cups prior to assembly.
3. Install new pistons.
4. Press new boots into cylinder counterbores by hand. Do
not lubricate boots prior to assembly.
Summary of Contents for 1982 Light Duty Truck
