IB -34
AIR CONDITIONING
1 0 2 0 3 9
Fig. 1 B-27--Condenser Installation (C-K Series)
Com pressor Belt Tension A d ju stm en t
A djust the com pressor belt to the specifications shown
in the Engine section of the Service M anual.
On some G and M otor Hom e Chassis units it m ay be
necessary to increase idler pulley slack adjustm ent. This
m ay be accom plished by (1) Remove and discard the idler
ad ju stm en t bolt. (2) Remove the idler backing plate and
elongate all 3 adjusting slots 1/2 in. inboard or outboard as
required. (3) Reinstall the idler assem bly and adjust belt
tension using a lever (screw driver, etc.) to move the pulley
outboard until proper belt tension is reached. If the belt is
being replaced it m ay be necessary to remove and replace
the th ro ttle cable during the belt replacem ent. If so check
throttle cable adjustm ent upon com pletion. It m ay also be
necessary to remove the cran k sh aft pulley to install a new
com pressor belt.
C60 SYSTEM--C-K SERIES
CO N DENSER - C-K SERIES (FIG . IB -2 7 )
R eplacem ent (Fig. IB -2 7 )
1. Disconnect battery ground cable.
2. D ischarge system.
3. Remove the grille assembly.
4. Remove the radiator grille center support.
5. Remove the left grille support to upper fender support
(2) screws.
6. Disconnect the condenser inlet and outlet lines and the
outlet tu b e line at the right end of the condenser. C ap or
plug all open connections at once.
7. Remove the condenser to rad iato r support screws.
8. Bend the left grille support outboard to gain clearance
for condenser removal.
9. Remove the condenser assem bly by pulling it forw ard
and then lowering it from the vehicle.
10. To install a new condenser, reverse Steps 1 th ru 9
above. A dd one fluid ounce of clean refrigeration oil to
a new condenser.
Use new " O " rings, coated w ith clean refrigeration oil,
when connecting all refrig e ran t lines.
11. E vacuate, charge and check the system.
A C C U M U LA T O R - ALL
R eplacem en t
1. D isconnect the b a tte ry ground cable and the
com pressor clutch connector.
2. D ischarge system.
3. Disconnect the accum ulator inlet and outlet lines and
cap or plug the open connections at once.
4. Remove the accum ulator bracket screws and remove
the accum ulator from the vehicle.
5. D rain any excess refrig eran t oil from the accum ulator
into a clean container. M easure and discard the oil.
6. If a new accum ulator is being installed, add one ounce
of clean refrigeration oil to the new accum ulator P L U S
an am ount equal to th a t drained in S tep 5 above.
7. To install the new accum ulator, reverse Steps 1 thru 4
above. Connect all lines using new " O " rings, coated
with clean refrigeration oil.
Do not uncap the new unit until ready to fasten the inlet
and outlet line to the unit.
8. Evacuate charge and check the system.
BLOWER ASSEMBLY - C-K SERIES
R eplacem en t
1. Disconnect the b attery ground cable.
2. Disconnect the blower m otor lead and ground wires.
3. Disconnect the blower m otor cooling tube.
4. Rem ove th e blow er to case a tta c h in g screw s and
remove the blower assembly. Pry the blower flange
away from the case carefully if the sealer acts as an
adhesive.
5. Remove the nut attach in g the blower wheel to the
m otor shaft and separate the assem blies.
6. To install, reverse Steps 1 thru 5 above; replace sealer
as necessary.
E VA PO R A TO R CORE
R eplacem en t (Fig. IB -2 8 )
1. Disconnect the b attery ground cable.
2. D ischarge system.
3. Rem ove the nuts from the selector d u ct studs
projecting through the dash panel.
Summary of Contents for 1982 Light Duty Truck
