![background image](http://html1.mh-extra.com/html/gmc/1982-light-duty-truck/1982-light-duty-truck_service-manual_2235920540.webp)
5-20
BRAKES
In stallatio n
Reverse the removal procedure. Torque all bolts and
nuts. After installing the clevis-pin, use a new cotter pin to
secure the clevis pin. Adjust the cable if necessary as
outlined below.
N O T IC E :
See "Notice" on Page 1 of this section.
A D J U S T M E N T
A djustm ent of parking brake cable is necessary
whenever holding ability is not adequate or whenever the
center brake cables have been disconnected.
The service brake must be properly adjusted as a base
for parking brake adjustment; conversely the parking brake
must be properly adjusted for the service brake to function
as intended.
Inspection
If com plete release o f the parking brake is not
obtained, unless it is forcibly returned to its released
position, or if application effort is high, check parking brake
assembly for free operation. If operation is sticky or a bind is
experienced, correct as follows:
1. Clean and lubricate brake cables and equalizer with
Delco Brake Lube (or equivalent).
2. Inspect brake assembly for straightness and alignment
(replace if necessary).
3. Clean and lubricate parking brake assembly with Delco
Brake Lube (or equivalent).
4. Checking routing of cables for kinks or binding.
A d ju stm e n t— Foot P e d a l Type
Before adjusting parking brake, check service brake
condition and adjustment.
1. Raise vehicle on hoist.
2. Loosen the equalizer adjusting nut.
3. Apply parking brake 4 notches from fully released
position.
4. Tighten the equalizer nut until a moderate drag is felt
when the rear wheels are rotated forward.
N O T IC E :
See "Notice" on Page 1 of this section.
5. Fully release parking brake and rotate the rear wheels.
N o drag should be present.
6. Remove vehicle from hoist.
A d ju stm e n t— O rscheln Lever Type
1. Turn adjusting knob on parking brake lever
counterclockwise to stop.
2. Apply parking brake.
3. Raise vehicle on a hoist.
4. Loosen nut at intermediate cable equalizer and then
adjust nut to give light drag at rear wheels.
N O T IC E :
See "Notice" on Page 1 of this section.
5. Readjust parking brake lever knob to give a definite
snap-over-center feel.
PARKING BRAKE (PROPELLER SHAFT)-
INTERNAL EXPANDING
A d ju stm e n t-D ru m O n
1. Jack up at least one rear wheel. Block wheels and
release hand brake.
2. Remove cotter pin and clevis pin connecting pull rod
and relay lever. This will assure freedom for full shoe
release.
N O T IC E :
It may be necessary to knock out lanced area
in brake drum with punch and hammer to gain entry
into adjusting screw through brake drum. Be sure all
metal has been removed from parking brake
compartment.
3. Rotate brake drum to bring one of access holes into line
with adjusting screw at bottom of shoes (manual
transmission), top of shoes (automatic transmission).
4. Expand shoes by rotating adjusting screws with
screwdriver inserted through hole in drum. Move outer
end of screwdriver away from drive shaft. Continue
adjustment until shoes are tight against drum and
drum cannot be rotated by hand. Back off adjustment
ten notches and check drum for free rotation.
5.
Place parking brake lever in fully released position.
Take up slack in brake linkage by pulling back on cable
just enough to overcome spring tension. Adjust clevis of
pull rod or front cable to line up with hole in relay
levers.
a. Insert clevis pin and cotter pin, then tighten clevis
locknut.
b. Install a new metal hole cover in drum to prevent
contamination of brake.
c. Lower rear wheels. Remove jack and wheel blocks.
N O T IC E :
See "Notice" on Page 1 of this section.
A d ju s t m e n t -D r u m O ff
1. With parking brake drum off, use special Tool J -2 1177
or J-22364, Drum to Brake Shoe Clearance Gauge, to
check diameter of drum clearance surface.
2. Turn the tool to the opposite side and fit over brake
shoes by turning the star wheel until the gauge just
slides over the linings.
3. Rotate the gauge around the brake shoe lining surface
to insure proper clearance.
4. Install propeller shaft flange at mainshaft as outlined in
transmission section.
5.
Lower rear wheels. Remove jack and wheel blocks.
P A R K IN G BRAKE CABLES (Fig. 5 -1 0 )
Front C a b le R e p lac e m e n t
1. Raise vehicle on hoist.
2. Remove adjusting nut from equalizer.
3. Remove retainer clip from rear portion of front cable at
frame and from lever arm.
4. Disconnect front brake cable from parking brake pedal
or lever assemblies. Remove front brake cable. On
some models it may assist installation of new cable if a
heavy cord is tied to other end of cable in order to guide
new cable through proper routing.
5.
Install cable by reversing removal procedure.
6. Adjust parking brake.
C e n te r C a b le R e p lac e m e n t
1. Raise vehicle on hoist.
2. Remove adjusting nut from equalizer.
3. Unhook connector at each end and disengage hooks and
guides.
4. Install new cable by reversing removal procedure.
Summary of Contents for 1982 Light Duty Truck
