GE MOTOR MANAGER 2 Instruction Manual Download Page 62 | Manualshive

Page: 62 / 220

background image

4-28

MM2 Motor Manager 2

GE Power Management

4.5 S4 CONTROL

4 SETPOINTS

4

4.5 S4 CONTROL

4.5.1 DESCRIPTION

This page is used to configure all control features in the MM2. Setpoints Page 4 is divided into three
sections, UNDERVOLTAGE AUTO-RESTART, AUX RELAY 1 CONFIG and AUX RELAY 2 CONFIG.

4.5.2 UNDERVOLTAGE AUTORESTART

PATH: SETPOINTS

tttt

S4: CONTROL

t

UNDERVOLTAGE AUTO RESTART

UNDERVOLTAGE

RESTART: ENABLE

Range: ENABLE, DISABLE

It is possible to restart the motor after a momentary power loss if this
feature is enabled. When the control voltage (derived from the incoming
motor supply) drops below the dropout voltage, both contactors are de-
energized. Voltage thresholds for the two internally set control voltage
levels are 80 V for 120 V setting and 150 V for 240 V setting. At nomi-
nal voltage, the MM2 rides through a power outage less than 135 ms
(varies according to the number of output relays energized at the time
of power failure). Critical data is saved to E

2

PROM at this time. A power

outage that exceeds the MM2 ride-through initializes a backup timer
that continues to run without power for approximately 1 hour. Once con-
trol power is restored, the MM2 can take up to 300 ms to initialize; this
time includes the initializing of the microprocessor, variables in the
code, the determination that a restart is required, and the closure of the
internal output relay. The reaction time of the contactor will be in addi-
tion to the 300 ms power-up time. If control voltage is restored within
the

IMMED. RESTART POWER LOSS TIME

(0.1 to 0.5 sec.), the motor will be

restarted immediately. If the supply is restored after the

IMMED. RESTART

POWER LOSS TIME

but before the

DELAY RESTART POWER LOSS TIME

, the

motor will be restarted after the

RESTART TIME DELAY

. If a delayed restart

is always required, set the

DELAY RESTART POWER LOSS TIME

to

UNLIM-

ITED

. Select

DISABLE

if this feature is not required.

IMMED. RESTART POWER

LOSS TIME:

200 ms

Range: 100 to 500 ms or OFF; Step: 20 ms

This is the time measured by the MM2 backup processor; it is not the
time the AC power has been off. See

UNDERVOLTAGE RESTART

for

details.

DELAY RESTART POWER

LOSS TIME:

2.0 s

Range: 0.1 to 10 seconds or TIME UNLIMITED; Step: 0.1 sec.

This is the time measured by the MM2 backup processor; it is not the
time the AC power has been off. See

UNDERVOLTAGE RESTART

for

details.

RESTART TIME DELAY

2.0 s

Range: 0.2 to 1200.0 seconds; Step: 0.2 seconds

See

UNDERVOLTAGE RESTART

for details.

«
...
60
61
62
63
64
...
»

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Reviews:

No comments

Related manuals for MOTOR MANAGER 2

Brand: FAAC Pages: 32

Brand: Jedo Pages: 26

Brand: Abocom Pages: 10

Brand: Matelec Pages: 16

Brand: Vageo Pages: 2

MagicSpeed Series

Brand: Waeco Pages: 76

Brand: Brand Innovations Pages: 56

Brand: Gemini Pages: 9

Brand: M-system Pages: 18

Brand: Altronix Pages: 8

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Brand: Seneca Pages: 4

Brand: Dickey-John Pages: 109

by-me Eikon 20526

Brand: Vimar Pages: 6

Brand: Argo-Hytos Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands