GE MOTOR MANAGER 2 Instruction Manual Download Page 93 | Manualshive

Page: 93 / 220

background image

GE Power Management

MM2 Motor Manager 2

6-13

6 COMMUNICATIONS

6.3 ERROR RESPONSES

6

6.3 ERROR RESPONSES

6.3.1 DESCRIPTION

When a MM2 detects an error other than a CRC error, a response will be sent to the master. The
MSBit of the FUNCTION CODE byte will be set to 1 (i.e. the function code sent from the slave will be
equal to the function code sent from the master plus 128). The following byte will be an exception
code indicating the type of error that occurred.

Transmissions received from the master with CRC errors will be ignored by the MM2.

The slave response to an error (other than CRC error) will be:

SLAVE ADDRESS: 1 byte

FUNCTION CODE: 1 byte (with MSbit set to 1)

EXCEPTION CODE: 1 byte

CRC: 2 bytes

The MM2 implements the following exception response codes.

•

01 - ILLEGAL FUNCTION
The function code transmitted is not one of the functions supported by the MM2.

•

02 - ILLEGAL DATA ADDRESS
The address referenced in the data field transmitted by the master is not an allowable address for
the MM2.

•

03 - ILLEGAL DATA VALUE
The value referenced in the data field transmitted by the master is not within range for the
selected data address.

«
...
91
92
93
94
95
...
»

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Reviews:

No comments

Related manuals for MOTOR MANAGER 2

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 2

Brand: Jafar Pages: 9

Brand: Panasonic Pages: 16

Brand: TCS Basys Controls Pages: 2

Brand: Caen Pages: 20

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: Magellan Pages: 2

Brand: Abov Pages: 138

Waukesha Cherry-Burrell D4 Series

Brand: SPX FLOW Pages: 34

Brand: Cardin Elettronica Pages: 56

Brand: Pfeiffer Vacuum Pages: 100

Brand: Westfalia Pages: 18

Brand: EOS Pages: 7

Easywave ST01 Series

Brand: Eldat Pages: 2

Brand: Zencontrol Pages: 2

Brand: Daikin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands