GE MOTOR MANAGER 2 Instruction Manual Download Page 186 | Manualshive

Page: 186 / 220

background image

9-38

MM2 Motor Manager 2

GE Power Management

9.13 SOFT STARTER

9 STARTER TYPES

9

9.13 SOFT STARTER

9.13.1 DESCRIPTION

When the RUN contact closes the soft starter ramps up the motor to the programmed speed. When
the RUN contact opens, the soft starter ramps down the motor to a stop.

To program the MM2 for soft starter, set:

S1 CONFIGURATION\STARTER\STARTER TYPE:

SOFT STARTER

S1 CONFIGURATION\STARTER\RAMP UP TIME:

1 to 125 sec.

S1 CONFIGURATION\STARTER\RAMP DOWN TIME:

1 to 125 sec.

S3 PROCESS\PROGRAMMABLE INPUTS\INTERLOCK INPUT 10:

BYPASS CONTACT (optional)

S4 CONTROL\AUX RELAY 1 CONFIG\AUX. RELAY 1 FUNCTION:

SOFT STARTER BYPASS (optional)

The

RAMP UP TIME

and

RAMP DOWN TIME

setpoints appear when

STARTER TYPE

has been selected as

SOFT STARTER

. See the MM2 sequence below for details on functionality.

9.13.2 MM2 SEQUENCE

START:

1. Start command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Contactor A output relay – provide power to the SOFT STARTER.

3. Wait for one second.

4. Close and maintain Contactor B output relay – signal the SOFT STARTER to start the motor.

5. Wait for the

RAMP UP TIME

for Contactor B Status N.O. to close.

6. Close Bypass contact AUX. relay (optional)

STOP/TRIP:

1. Stop command is received or a trip occurs (serial, switch input or faceplate).

2. Open contactor B output relay.

3. Open Bypass contact AUX. relay (optional).

4. Wait for the

RAMP DOWN TIME

for Contactor B Status N.O. to open.

5. When Contactor B Status N.O. reads open, open Contactor A output relay.

If feedback is not received from the 1M contact to the Contactor A Status N.O. input within one sec-
ond of closing Contactor A output relay, an OPEN CONTROL CIRCUIT alarm will occur. This will
cause Contactor A and B output relays to open.

If Contactor B Status N.O. does not receive feedback from the up to speed contact on the SOFT
STARTER within the RAMP UP TIME setpoint during a start, a DRIVE FAILED TO START alarm will
be generated. If Contactor B Status N.O. feedback remains at the MM2 after the

RAMP DOWN TIME

has expired during a stop, a DRIVE FAILED TO STOP alarm will be generated.

If feedback remains at Contactor A Status N.O. input more than 1 second after opening the Contac-
tor A output relay, a WELDED CONTACTOR alarm occurs. If feedback remains at the Interlock con-
figured for BYPASS CONTACT more than one second after opening the Aux output relay, a
WELDED CONTACTOR alarm occurs. If feedback is not received from the BYPASS CONTACT
interlock input within one second of closing Aux output relay, an OPEN CONTROL CIRCUIT alarm
occurs. This will cause Contactor A and B output relays to open.

«
...
184
185
186
187
188
...
»

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Reviews:

No comments

Related manuals for MOTOR MANAGER 2

Brand: Canon Pages: 2

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: FATEK Pages: 10

Brand: OEM Pages: 8

Brand: ABB Pages: 102

NOVASTAT EL DIGITAL

Brand: Taconova Pages: 7

Brand: Gardena Pages: 236

Brand: OJ Electronics Pages: 8

Brand: Osaka Pages: 12

Brand: Cooper Pages: 4

Brand: Trenz Electronic Pages: 21

Brand: Widex Pages: 17

Brand: DAYLIFF Pages: 40

Rite-Temp K-8304-K

Brand: Kohler Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands