GE MOTOR MANAGER 2 Instruction Manual Download Page 145

Page: 145 / 220

GE Power Management

MM2 Motor Manager 2

8-11

8 MM2PC

SOFTWARE

8.4 USING MM2PC

8.4.5 VIEWING ACTUAL VALUES

The following example shows how to view and trend MM2 actual values.

1. Establish communications with the MM2 unit and select the Actual > Statistics menu item. This

opens the window showing the relevant monitored values. These values are continuously
updated while the window is open.

2. The MM2PC

trending feature can be used to plot measured parameters. The following values

can be trended:

•

Phase currents (

), ground current (

gnd

), motor load, thermal capacity, current unbal-

ance, analog input, voltage, and power.

3. Select the Actual > Trending menu item to open the trending window (see figure on following

page). Press the Setup button on the lower left of the window to enter the Graph Attribute page.

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Search results

Summary of Contents for MOTOR MANAGER 2

Reviews:

Related manuals for MOTOR MANAGER 2

Brands by name

Popular brands

GE MOTOR MANAGER 2, Instruction Manual

Search results

Summary of Contents for MOTOR MANAGER 2

Reviews:

Related manuals for MOTOR MANAGER 2

Brands by name

Popular brands