GE MOTOR MANAGER 2 Instruction Manual Download Page 155 | Manualshive

Page: 155 / 220

background image

GE Power Management

MM2 Motor Manager 2

9-7

9 STARTER TYPES

9.3 TWO SPEED STARTER

9

9.3.2 MM2 SEQUENCES

START LOW SPEED sequence:

1. Start A command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Contactor A relay – the motor is now in low speed.

START DIRECTLY TO HIGH SPEED (motor stopped,

HIGH SPEED START BLOCK

not enabled)

sequence:

1. Start B command received by the MM2 (serial, switch input or faceplate).

2. Close and maintain Contactor B relay – the motor is now in high speed.

START DIRECTLY TO HIGH SPEED (motor stopped,

HIGH SPEED START BLOCK

enabled) sequence:

1. Start B command received by the MM2 (serial, switch input or faceplate).

2. No response to start B commands.

LOW TO HIGH SPEED TRANSITION sequence:

1. Start B command is received (serial, switch input or faceplate).

2. Open contactor A output relay.

3. Close and maintain Contactor B relay – the motor is now in high speed.

HIGH TO LOW SPEED TRANSITION sequence:

1. Start A command is received (serial, switch input or faceplate).

2. Open contactor B output relay.

3. Wait for the programmed transfer time.

4. Close and maintain contactor A.

STOP/TRIP sequence:

1. Stop command received by the MM2 or a trip occurs.

2. Open the currently closed contactor output relay.

There are many different configurations for the TWO SPEED starter type. Three of the more popular
ones are illustrated here: two-speed one winding constant or variable torque, two-speed one winding
constant horsepower, and two-speed two winding. See the two speed starter diagrams on the follow-
ing pages.

When the power to the MM2 is interrupted, all MM2 output relays de-energize, causing them to open
and stop the motor. The MM2 can only be wired for fail-safe operation.

If feedback is not received from the L or H contacts to the Contactor A or B Status N.O. input within
one second of closing Contactor A relay, an OPEN CONTROL CIRCUIT alarm will occur. This will
cause Contactor A and B output relays to open.

If feedback remains at the Contactor A or B Status N.O. input more than one second after opening
the Contactor A or B output relays, a WELDED CONTACTOR alarm will occur.

«
...
153
154
155
156
157
...
»

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Reviews:

No comments

Related manuals for MOTOR MANAGER 2

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: 3M Pages: 34

Brand: H3C Pages: 69

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Watlow Pages: 59

Tekmar WiFi Snow Melting Control 670

Brand: Watts Pages: 48

disklavier DKC-850

Brand: Yamaha Pages: 2

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 66

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands