GE MOTOR MANAGER 2 Instruction Manual Download Page 154 | Manualshive

Page: 154 / 220

background image

9-6

MM2 Motor Manager 2

GE Power Management

9.3 TWO SPEED STARTER

9 STARTER TYPES

9

9.3 TWO SPEED STARTER

9.3.1 DESCRIPTION

When the low speed button is pressed, the CR coil will pick up and seal itself in. The L contactor is
then picked up and the motor starts in low speed. When the high speed button is pressed, the L con-
tactor drops out and the H contactor picks up and seals itself in. Timing relay TR is also picked up. If
the low speed button is pressed, the TR relay will prevent the motor from going to low speed until it
times out and the motor has had time to slow down.

Figure 9–5: ELEMENTARY TWO SPEED MAGNETIC STARTER

To program the MM2 for two-speed starter, set:

S1 CONFIGURATION\STARTER\STARTER TYPE:

TWO-SPEED

S1 CONFIGURATION\STARTER\TRANSFER TIME:

1 to 125 sec.

S1 CONFIGURATION\STARTER\HIGH SPEED START BLOCK:

ENABLE or DISABLE

The

TRANSFER TIME

setpoint appears when the

STARTER TYPE

has been selected as

TWO-SPEED

. This

delay may be required when the motor is switched from high-speed (Contactor B) directly to low-
speed (Contactor A). The delay starts when Contactor B drops out.

The

HIGH SPEED START BLOCK

setpoint appears when the

STARTER TYPE

has been selected as

TWO-

SPEED

. When set to

DISABLED

, the MM2 allows the motor to be started directly to high speed. When

set to

ENABLED

, the motor must be started in low-speed before switching to high-speed.

«
...
152
153
154
155
156
...
»

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Reviews:

No comments

Related manuals for MOTOR MANAGER 2

Brand: ZKTeco Pages: 123

Concord express

Brand: GE Pages: 3

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: U-Prox Pages: 31

Brand: CALEFFI Pages: 2

Brand: CALEFFI Pages: 12

Brand: Caliber Pages: 6

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Saitek Pages: 15

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: L-Acoustics Pages: 24

Brand: L-Acoustics Pages: 21

Brand: M&S Systems Pages: 4

Brand: Ultraflex Pages: 7

Brand: WAGO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands