GE MOTOR MANAGER 2 Instruction Manual Download Page 216 | Manualshive

Page: 216 / 220

background image

G-2

MM2 Motor Manager 2

GE Power Management

0.1 GE POWER MANAGEMENT WARRANTY

APPENDIX G

G

0.1 GE POWER MANAGEMENT WARRANTY

GE POWER MANAGEMENT RELAY WARRANTY

General Electric Power Management Inc. (GE Power Management)
warrants each relay it manufactures to be free from defects in material
and workmanship under normal use and service for a period of 24
months from date of shipment from factory.

In the event of a failure covered by warranty, GE Power Management will
undertake to repair or replace the relay providing the warrantor
determined that it is defective and it is returned with all transportation
charges prepaid to an authorized service centre or the factory. Repairs
or replacement under warranty will be made without charge.

Warranty shall not apply to any relay which has been subject to misuse,
negligence, accident, incorrect installation or use not in accordance with
instructions nor any unit that has been altered outside a GE Power
Management authorized factory outlet.

GE Power Management is not liable for special, indirect or consequential
damages or for loss of profit or for expenses sustained as a result of a
relay malfunction, incorrect application or adjustment.

For complete text of Warranty (including limitations and disclaimers),
refer to GE Power Management Standard Conditions of Sale.

«
...
214
215
216
217
218
...
»

Summary of Contents for MOTOR MANAGER 2





























































































































































































































Reviews:

No comments

Related manuals for MOTOR MANAGER 2

Brand: ZKTeco Pages: 123

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

Brand: X-lander Pages: 72

Brand: X Rocker Pages: 38

Brand: xpr Pages: 4

Brand: MULTISPAN Pages: 2

PetroVend PV200

Brand: OPW Pages: 2

Brand: HORI Pages: 60

Brand: Simpnic Pages: 16

Brand: Partlow Pages: 49

Brand: Ascon tecnologic Pages: 11

Brand: ROBOT3T Pages: 21

Brand: StudioComm Pages: 61

Brand: Consort Pages: 4

Brand: Caleffi solar Pages: 16

Brand: KWC Pages: 8

Arteor 5 742 74

Brand: LEGRAND Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands