GE iBox Installation And Maintenance Manual Download Page 17

Page: 17 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

System Software

, continued

68K Monitor

The iBox 68K Monitor, available through WESMAINT, is a diagnostic tool used to

access system-level functions.
The iBox 68K Monitor is resident in both BootROM and flash memory.
When the Monitor is operated from BootROM, the following prompt appears:

D25S>

. This mode is accessed

only

while the iBox is in a maintenance state, since

forcing an iBox into this mode terminates all running applications.
When the Monitor is operated from flash, the following prompt appears:

D25A>

This is the normal mode of operation, and it can be accessed via WESMAINT at any

time without disrupting unit operation.

Note

Using the 68K Monitor requires detailed knowledge of the iBox architecture and

functionality. Refer to the

68K Monitor User’s Guide

(SWM0023) for complete

instructions about command usage and availability.

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands