GE iBox Installation And Maintenance Manual Download Page 169

Page: 169 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

169

Appendix G: Error Messages

When processing an output request, the Plant I/O Subsystem (P097) DCA may not be able to execute the

request. If this occurs, the Plant I/O Subsystem DCA will set the status code returned with the request to

the appropriate error code, and negatively acknowledge (NACK) the control request. This section

describes the possible status codes returned.

Control Requests Error Codes

Error Message

Description

Unsupported Point (0x0010)

Requested control point is not supported.

Unsupported Operation (0x0011)

Requested control operation is not supported for this point.

Output Not Available (0x0012)

The control output is not available for this point.

Queue Not Available (0x0013)

The control output queue is not available.

Invalid Request Parameters

(0x0014)

The control output request parameters are not valid for this control

point.

Too Much Lead Time (0x0015)

The control output request lead time is too much.

Not Enough Lag Time (0x0016)

The control output request lag time is not enough.

Window Too Small (0x0017)

Control output request time window is too small.

No Room on Queue (0x0018)

The control output request queue is full.

Not Armed (0x0019)

The control request point is not armed.

Analog Requests Error Codes

Error Message

Description

Analog Output Unsupported Point (0x0010)

The analog output point is not supported.

Analog Output Not Available (0x0011)

The analog output is not available.

Online Configuration in Progress (0x0012)

Another online configuration change is in progress.

Online Configuration Invalid Type (0x0013)

Configured alarm settings do not match the alarm

type.

Online Configuration Invalid Settings (0x0014)

Configured alarm settings are out of range.

Online Configuration Alarm Not Available (0x0015)

Specified alarm number is unavailable.

Online Configuration Invalid Alarm Number

(0x0016)

Specified alarm number is out of range.

Online Configuration No Alarm Number (0x0017)

No alarm number has been submitted.

Online Configuration Cancelled (0x0018)

Configuration change is cancelled.

Online Configuration Time Out (0x0019)

Configuration change cancelled due to timeout.

Online Configuration Disabled (0x001A)

Online configuration services are disabled.

Online Configuration Change Disabled (0x001B)

Online configuration change service is disabled

Online Configuration Out of Events (0x001C)

Request rejected. Lacked WIN event buffers.

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands