GE iBox Installation And Maintenance Manual Download Page 76

Page: 76 / 172

iBox/iBox Kit

Installation and Maintenance Guide

GE Grid Solutions

994-0047-5.10-4

GE Information

Replacing your iBox

, continued

Procedure:

Replacing an

iBox

Use the following procedure to replace an iBox:

Step

Action

Removing the Existing iBox

Power down the iBox by unplugging power from TB1.

Disconnect ground from the iBox.

Ensure no voltage or current is applied to any of the terminals on the

iBox. Use a meter if necessary.

Remove field wiring connections

Important:

When the new unit is installed it is important that these

wires are reconnected to the same points from which they

were removed. Record the position of each wire as it is

removed.

Remove communications cables from the iBox

Important:

Note the location and orientation of each cable as it is

removed

Remove the disconnected iBox from its mounting position

Installing the Replacement iBox

Mount the new iBox.

Reconnect the field wiring to the same points as they were on the

original unit.

Reconnect any communications cables that were removed to the same

points as they were on the original unit.

Restore ground and power to the iBox.

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands