GE iBox Installation And Maintenance Manual Download Page 120

Page: 120 / 172

iBox/iBox Kit

Installation and Maintenance Guide

GE Grid Solutions

120

994-0047-5.10-4

GE Information

Configuring the Ethernet Module

, continued

Procedure:

Configuring

the Digi One

(continued)

Step

Action

Downloading the Configuration File to the Digi One

Under

Administration

, click

Backup/Restore

Result:

The

Backup/Restore

page appears:

Click

Browse

and enter the location of the Digi One configuration file on

your PC.

Click

Restore

Result:

The Digi One receives the configuration file from your PC.

Click

Done

Result:

The

Reboot

page appears.

Note:

The Digi One IAP needs to be rebooted for the new configuration

settings to be applied.

Click

Reboot

Result:

The Digi One reboots.

Continued on next page

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands