manualshive.com logo in svg

GE iBox, Installation And Maintenance Manual, Page: 114 / 172

Share
Download
GE iBox Installation And Maintenance Manual Download Page 114

iBox/iBox Kit  

Installation and Maintenance Guide 

GE Grid Solutions 

 

114

 

994-0047-5.10-4 

GE Information 

 

Configuring the Ethernet Module

, continued

 

Procedure:  

Configuring 

the Digi One 

(continued) 

Step 

Action 

20

 

 Select your device.  

Note:

 

The MAC address of your Digi One IAP is located on the white 

label on the bottom or back of the device. 

21

 

 Click 

Next

. 

Result:

 

The 

Configure Network Settings

 page appears: 

 

Configure the Digi One IP Settings 

22

 

 Select 

Use the following IP settings

. 

23

 

 Enter the Digi One Ethernet IP address and subnet mask, as shown in the 

above example. Enter a gateway address if one is required. Check with 

your network administrator if you are not sure. 

 

Continued on next page 

Summary of Contents for iBox













































































































































































Reviews:

No comments