GE iBox Installation And Maintenance Manual Download Page 31

Page: 31 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

Terminal Connections

Power Supply

The iBox’s power supply connection is a three-position terminal block located on the

bottom left side of the iBox. This removable terminal block must be disconnected to

turn off the power supply input. The iBox does not have an ON/OFF switch.

Functional

Ground/

Chassis

Connect the ground screw terminal to the facility’s ground system before operating

the iBox. Before making this connection, ensure all grounding surfaces are free of

dirt, residue and corrosion. The maximum wire gauge for terminal blocks is 12

AWG.

Internal

Overcurrent

Protection

An internal MDL 0.5 A (slow blow) fuse protects the iBox power supply.

Power

Connection

Procedure

To connect the power source:

Step

Action

Connect ground wire to the ground terminal. A 12 AWG green and

yellow wire is recommended.

Connect the DC power supply, observing the correct polarity, to the

positive and negative connection points on TB1

The chassis ground terminal at the power supply terminal block

must not

be used as

a protective earth connection.

Make sure the iBox is properly grounded to the protective earth terminal located at

the bottom-left corner of the board. Connection must be provided with a separate

green/yellow wire connected between the iBox and the facility’s ground system.

–

Chassis

TB1

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands