GE iBox Installation And Maintenance Manual Download Page 141

Page: 141 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

141

4.2. From the PC Running Configuration Software

Method

If SGConfig have been used to configure the iBox processor, configuration data

resides on the data storage media (e.g., hard drives, memory cards, etc.) of the PC

running SGConfig.
The iBox configuration data can be removed from the PC by either:

•

Recommended: Physically removing and destroying the data storage media,

•

Using a program to securely wipe (i.e., completely erase) the data storage

media; that is, not just reformat or remove the names of the files from the file

allocation table.

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands