GE iBox Installation And Maintenance Manual Download Page 53

Page: 53 / 172

GE Grid Solutions

iBox/iBox Kit

Installation and Maintenance Guide

GE Information

994-0047-5.10-4

Digital Input Configuration

Digital Input

Field

Connections

Field wiring for all digital input variants are made through the iBox’s terminal

blocks, separable in pairs.

Digital Input

Wetting

Selection

The digital input is wetted (or turned ON) by closing a contact across the two input

termination points. The voltage that is switched at the input terminals is supplied by

an external source. The external power source is connected to terminal block TB-10,

positions 1 and 2, as shown below.

All eight digital inputs are bipolar. Use care when connecting multiple external

power sources, since the digital inputs have common returns.

Wiring

Diagram:

Dry Contact

Operation

This diagram illustrates the DC input connections, from Input #1 (TB2) through

Input #8 (TB9). TB10 accepts DC voltages of either polarity. The input voltage level

to TB10 is determined by the purchased option.

Input #1

Input #8

External Wetting

Power Supply

TB2

TB9

TB10

+/- V

Summary of Contents for iBox













































































































































































Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands

GE iBox, Installation And Maintenance Manual

Search results

Summary of Contents for iBox

Reviews:

Related manuals for iBox

Brands by name

Popular brands