Furuno FV-110 Operator'S Manual Download Page 164 | Manualshive

Page: 164 / 240

background image

STM SatLink 2900 VSAT modem

C-22

C.6

STM SatLink 2900 VSAT modem

C.6.1

Interfaces and VSAT modem configuration

The following sections describe how to connect an ACU to an STM SatLink 2900 VSAT
modem. The STM SatLink 2900 and the FV-110 are fully integrated and require almost
no user setup.

STM SatLink 2900 software version required: 14.2.0 or higher.

Connections and login

1. Connect the ACU and STM SatLink 2900 with the following cables:

• Ethernet cable for TCP/IP data communication. Connect LAN A on the VSAT modem

to LAN 1 on the ACU.

• 75 Ohm RF cables F-F connectors for RX and TX frequencies

Figure C-17: Connecting STM SatLink 2900 VSAT modem to the ACU

2. Connect a PC to the modem via serial (setting: 38400, 8, N, 1) or telnet.

3. Login to the modem with the user name and password received from the VSAT service

provider.

Example

: Login: root

             Password: *******
             SatLink 2900
             - Main board ID 120265, Revision R4.0
             - SW ID 120208, Revision 16.0.0 Build 46

4. Check that the modem has software version 14.2.0 or higher. Earlier modem software

versions are not supported.

«
...
162
163
164
165
166
...
»

Summary of Contents for FV-110

















































































































































































































































Reviews:

No comments

Related manuals for FV-110

Brand: H3C Pages: 6

Brand: Yaesu Pages: 1

Brand: Crest Audio Pages: 4

Brand: Chameleon Antenna Pages: 15

Brand: MaxRange Pages: 7

Brand: Sanav Pages: 4

Brand: K&M Burkhard Reuter Pages: 8

Brand: Q-Mac Pages: 21

Brand: Emos Pages: 16

Brand: Emos Pages: 28

Brand: RCA Pages: 1

Brand: HQ Power Pages: 12

RoamAbout 802.11

Brand: Cabletron Systems Pages: 24

Brand: Winegard Pages: 8

Brand: One for All Pages: 2

Brand: One for All Pages: 2

Brand: One for All Pages: 2

Brand: Greyline Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands