Furuno FV-110 Operator'S Manual Download Page 42

Page: 42 / 240

Installation of the ADU

2-18

2.3

Installation of the ADU

The ADU is shipped fully assembled. You have to install it on the mast and attach the
ADU cable.

Before installing the ADU read the following guidelines.

WARNING!

Use a strong webbed sling with a belt to

lift the ADU without damaging the radome. Make sure
that the sling can carry the ADU’s weight126,5 kg (FV-
110).

WARNING!

The ADU may be subject to swaying

motions in windy conditions. Always use tag lines to
stabilise the ADU during hoisting.

Figure 2-14: FV-110: Use of strong sling with a belt and tag lines for safe

hoisting

Tag lines

Webbed sling with belt

Summary of Contents for FV-110

















































































































































































































































Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands

Furuno FV-110, Operator'S Manual

Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands