Furuno FV-110 Operator'S Manual Download Page 25

Page: 25 / 240

2-1

Chapter 2

Installation

This chapter is organised in the following sections:

•

Unpacking

•

Site preparation

•

Installation of the ADU

•

Installation of the ACU

•

Installation of the VMU

2.1

Unpacking

2.1.1

What’s in the box

ADU

Unpack your FV-110 ADU and check that the following items are present:

• ADU with 4 lifting brackets (already mounted)

• Package with bolts, washers and cable glands (2 sizes)

ACU

Unpack your FV-110 ACU and check that the following items are present:

• 1 x Ethernet cable (2 m)

• 1 x Ethernet cable (short)

• Power cable (230 VAC)

• 2 x 75 Ohm coax cables F-F (1m), for Rx and Tx

• NMEA multi-connector

• Installation manual

Summary of Contents for FV-110

















































































































































































































































Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands

Furuno FV-110, Operator'S Manual

Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands