Furuno FV-110 Operator'S Manual Download Page 86 | Manualshive

Page: 86 / 240

Furuno FV-110 Operator'S Manual Download Page 86

Configuration with the web interface

5-24

For modems communicating via Ethernet:

Make sure that you have entered the

correct IP address also for the LAN connector that is used for the modem, see

To

configure the LAN network

on page 5-29.

5. Click

Apply

to add the new profile to the list of VSAT modem profiles or to accept the

edits.

For a generic modem you enter all parameters in the satellite profile.

Figure 5-18: Satellite profile for generic modem

Satellite profiles

On the page

Satellite profiles

you add, edit and delete satellite profiles. A satellite profile

contains all settings that are necessary for a successful connection to the satellite,
including a VSAT modem profile. Most of the data you have to fill in are provided by
your VSAT service provider. Each satellite profile has one assigned modem profile. You
must activate one satellite profile. You must activate one satellite profile.

Important

The FV-110 can work either using the Rx or Tx 10 MHz reference signals
provided by the modem or using its own built-in 10 MHz reference signal. It
is recommended to use the Tx 10 MHz reference signal from the modem.

Note

You must add at least one VSAT modem profile before you can add a satellite
profile. See

Modem profiles

on page 5-22.

«
...
84
85
86
87
88
...
»

Summary of Contents for FV-110

















































































































































































































































Reviews:

No comments