Furuno FV-110 Operator'S Manual Download Page 123

Page: 123 / 240

7-1

Chapter 7

Service

In this chapter you find the following sections:

•

Getting support: Helpdesk

•

Software update

•

Status signalling with LEDs and status messages

•

Removal and replacement of the ACU

•

Removal and replacement of ADU modules

•

Troubleshooting

7.1

Getting support: Helpdesk

If this manual does not provide the remedies to solve your problem, contact your service
provider.

7.1.1

Help desk and diagnostic report

During the installation you can enter the support contact for this installation.

To access the Help desk, select

HELPDESK

from the left navigation pane.

Figure 7-1: Web interface: HELPDESK

Click the link, enter support contact information and click

Apply

You can download the MIB file.

At Legal notice the licence text for the source code of the parts of the FV-110 software
that falls under free and open source software can be displayed.

If you need help

with ACU or ADU related issues

call your service provider.

Summary of Contents for FV-110

















































































































































































































































Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands

Furuno FV-110, Operator'S Manual

Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands