background image

OpenAMIP setup for iDirect iNFINITI & Evolution

C-7

[FREQ_TRANS]
down_translation = 11300.000000

up_translation = 12800.000000    #!!(FV-110, BUC LO)!!

[MOBILE]

gps_input = 2                    #!!(2 = GPS via OpenAMIP)!!

gps_validation_active = 1

init_tx_power_offset = -10.000000   #!!(FV-110)!!
is_mobile = 1                       #!!(1 = Maritime)!!

latlong_acq_interval = 300
latlong_fail_interval = 10
latlong_interval = 300

tx_handshake_enabled = 0            #!!(FV-110)!!

[ODU]
lnb_dc_voltage = 18
lnb_tone_enable = 0
music_present = 0
odu_disable_tx_pwm = 0
odu_rx_10_mhz = 0
odu_rx_dc_power = 0

odu_tx_10_mhz = 1                   #!!(FV-110)!!

odu_tx_dc_power = 0

[SATELLITE]
channelname = E36B - Maritime
hunt_bandwidth = 0.000000
hunt_frequency = 1233.660000
longitude = 35.900000
max_lat = 0.000000
max_skew = 90.000000
min_look_angle = 0.000000
name = E36B
noise_reference_frequency = 0.000000
pol_skew = 0.000000
polarity = V
rx_lcl_osc = 11300.000000
skew_margin = 90.000000
tx_bandwidth = 0.000000

tx_frequency = 1234.560000   #!!(Tx freq. for best 
performance)!!
tx_lcl_osc = 12800.000000    #!!(FV-110, 12.8 GHz BUC LO)!!

tx_polarity = X

[UCP]
max_power_level_in_db = -5.000000

#!!(FV-110 P1dB = -5.0 dBm)

                              #!!(FV-110 6W P1dB = -6.2 dBm)

power_uplink_control_processing = 1

Summary of Contents for FV-110

















































































































































































































































Reviews: