manualshive.com logo in svg

Furuno FV-110, Operator'S Manual, Page: 132 / 240

Share
Download
Furuno FV-110 Operator'S Manual Download Page 132

Removal and replacement of ADU modules

7-10

In switch-off position the DC Motor Driver modules (DDM), the Polarisation Motor 
Module (PMM) and the BUC are turned off for safe conditions during service and 
repair. The switch must be in on position for normal ADU operation. 

5. DC-Motor Driver Module for cross elevation (DDM).

6. Cross elevation motor and encoder.

7. Zero Reference Module (x4, 3 in the previous figure, 1 in the next figure) (ZRM) (not 

visible on photo).

8. DC-Motor Driver Module for elevation (on the bottom side) (DDM).

9. Elevation motor and encoder (not visible on photo).

10.Polarisation Motor Module (PMM).

11.Polarisation motor.

12.Polarisation encoder (not visible on photo).

13.Block Up Converter (BUC). (behind cable screen, not visible on photo)

14.Low Noise Block down converter (x2) (LNB).

15.Ortho Mode Transducer (OMT) (behind cable screen, not visible on photo).

16.Inertial Sensor Module (ISM).

17.Elevation locking pin to lock the antenna dish in a fixed position (for safety during 

service) (not visible on photo).

Summary of Contents for FV-110

















































































































































































































































Reviews:

No comments