Furuno FV-110 Operator'S Manual Download Page 44

Page: 44 / 240

Installation of the ADU

2-20

5. Attach 2 tag lines of suitable length to 2 lifting brackets and man them.

6. With a crane lift the ADU off the wooden platform and move it on top of the ADU

mast.

7. Install the ADU on the mast flange with 4 M12 bolts and washers.Read carefully and

follow instructions given in

To ground the ADU

on page F-2.

Tightening torque value: 30 Nm.

8. Remove the 4 lifting brackets. For safekeeping fasten the lifting brackets inside the

bottom of the radome.

9. Put the coaxial ADU cable through the protection plate as shown in the following

figure (FV-110), and connect the N connector of the ADU cable to the ADU.

Figure 2-16: FV-110: ADU installation, webbed sling attached to the 4 lifting

brackets

Figure 2-17: Mounting the ADU on the mast flange

Summary of Contents for FV-110

















































































































































































































































Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands

Furuno FV-110, Operator'S Manual

Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands