Furuno FV-110 Operator'S Manual Download Page 128

Page: 128 / 240

Software update

7-6

7.2.3

To verify the software update

1. The software version can be viewed in the

DASHBOARD

window of the web

interface.

2. After completing the software update procedure, the ACU will perform a POST

(Power On Self Test).

3. When the POST has finished, the green Pass/Fail LED on the front of the ACU must

become steadily green. Verify that the Pass/Fail LED is not red nor flashing orange
once every 2 seconds. Wait until the Pass/Fail LED is green.

4. Verify that the software update has been completed successfully. You find the software

version number in the

DASHBOARD

window of the web interface.

Figure 7-5: Verifying software update, FV-110

x.xx

Summary of Contents for FV-110

















































































































































































































































Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands

Furuno FV-110, Operator'S Manual

Search results

Summary of Contents for FV-110

Reviews:

Related manuals for FV-110

Brands by name

Popular brands