manualshive.com logo in svg

Fuji Xerox DocuPrint C3055 DX, User Manual

Share
Download
Fuji Xerox DocuPrint C3055 DX User Manual Download Page 38

38

2 Basic Operation

2.2

Switching On/Off the Power

Switching On the Power

1.

Press the power switch to the <|> position.

2.

When the power is switched on, the display 
reads [Please wait...]. Wait until the 
message changes to [Ready to print].

Note

• When the display reads [Please wait...], the printer is 

warming up and is not ready to print yet.

• If an error message is displayed, refer to "Error 

Messages (in Alphabetical Order)" (P. 147) to remedy 
the error.

Switching Off the Power

Important

• Do not switch the power off while the hard disk (optional) is being accessed. In the Power Saver mode, 

the <Power Saver> button blinks when the hard disk is being accessed.

• Do not switch the power off when the display reads [Please wait...].
• Do not switch the power off during printing. Doing so can cause paper jams. 
• Switching the power off erases the print data remained in the printer and the information stored in the 

printer's memory.

1.

Make sure that printer is not in operation by 
checking the display or indicator lamps.

2.

Press the power switch to the <O> position.

Summary of Contents for DocuPrint C3055 DX















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands