manualshive.com logo in svg

Fuji Xerox DocuPrint C3055 DX, User Manual

Share
Download
Fuji Xerox DocuPrint C3055 DX User Manual Download Page 146

146

6 Troubleshooting

6.5

Paper Feeding Problems

Symptom

Cause/Remedy

Paper does not feed properly.

Paper jams occur.

Multiple sheets feed at once.

Paper feeds skewed.

Output is wrinkled.

Is the paper loaded correctly?
Reload the paper correctly. Before loading labels, transparencies, postcards, or 
envelopes, fan them to make sure that they are separated.

Isn't the paper damp?
Load fresh paper.

Is the paper appropriate for the printer?
Load appropriate paper. Paper may still wrinkle depending on its type or condition.

Refer to

• "Supported Paper" (P. 76)

Are the paper trays pushed in completely?
Push the trays firmly into the printer.

Is the printer installed on a level surface?
Install the printer on a level and sturdy surface.

Are the paper guides adjusted properly?
Adjust the paper guides properly.

Refer to

• "4.2 Loading Paper" (P. 81)

These problems can happen if you add paper on top of paper that is still in a paper tray. 
Fan the paper loaded in the tray and reload it into the tray. Add paper to the tray only 
when the tray is out of paper.

Are you trying to print on postcards with pre-printed pictures?
If you load postcards with printed pictures, the anti set-off powder sticks to the feed rolls 
preventing the postcards from being fed properly. In such case, clean the feed rolls.

Refer to

• "Cleaning the Feed Rolls" (P. 203)

The feed rolls may be worn out or have reached their end-of-life.
Clean the feed rolls.
If the problem persists, the feed rolls must be replaced depending on their conditions. 
Contact our Customer Support Center or your dealers.

Refer to

• "Cleaning the Feed Rolls" (P. 203)

The printer does not correctly 
select a paper tray from the 
trays 1 to 4.

Did you switch on the power when the trays are removed from the printer? 
If you did, the printer may not correctly sensor the size of paper loaded in the printer. 
Push the trays firmly into the printer, and switch the printer off and then on again.

Are the paper guides adjusted properly?
If the paper guides are not positioned correctly, the printer may not correctly sensor the 
size of the paper loaded. Adjust the paper guides properly.

Check whether the paper size and paper type settings on the print driver and the control 
panel are set correctly.

Refer to

• " [Printer Settings]" (P. 119)
• Online help for the print driver.

The printer does not feed 
paper from the bypass tray.

Isn't the [Paper/Output] tab > [Paper Source] set to [Auto]? The bypass tray cannot be 
auto-selected by the printer. 

Refer to

• Online help for the print driver.

Summary of Contents for DocuPrint C3055 DX















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands