Fuji Xerox DocuPrint C3055 DX User Manual Download Page 198

Page: 198 / 238

198

7 Maintenance

7.10

Adjusting the Image Transfer Voltage

If the following problems occur frequently, the image transfer voltage may not be
appropriate. Complete the following steps to adjust the voltage.

• White patches appear on images (reduce the voltage)

• Toner scatters around images (increase the voltage)

•

Overall images are bluish (increase the voltage)

The image transfer voltage can be adjusted for each paper type within the range of -30 to
30 in increments of 1. The default is “0”.

Press the <Menu> button on the control
panel to display the menu screen.

Press the < > button until [Admin Menu] is
displayed.

Press the < > button to accept the
selection.
[Network/Port] is displayed.

Press the < > button until [Maintenance
Mode] is displayed.

Press the < > button to accept the
selection.
[Adjust Paper Type] is displayed.

Press the < > button until [Adjust BTR] is
displayed.

Press the < > button to accept the
selection.
A screen that allows you to set the paper
type is displayed.

Press the < > button until the desired
paper type is displayed. (Example: Bond)

Press the < > button to accept the
selection.
The current setting is displayed.

10. Enter the new value using the < > or < >

button. (Example:10)

Print Language

Admin Menu

Network / Port

Admin Menu

Maintenance Mode

Adjust PaperType

Maintenance Mode

Adjust BTR

Plain

Adjust BTR

Bond

Summary of Contents for DocuPrint C3055 DX














































































































































































































































Search results

Summary of Contents for DocuPrint C3055 DX

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuPrint C3055 DX, User Manual

Search results

Summary of Contents for DocuPrint C3055 DX

Reviews:

Brands by name

Popular brands