manualshive.com logo in svg

Fuji Xerox DocuPrint C3055 DX, User Manual

Share
Download
Fuji Xerox DocuPrint C3055 DX User Manual Download Page 165

7.1 Replacing Consumables

165

5.

Shake the toner cartridge three or four 
times to even out the toner inside.

6.

Hold the toner cartridge horizontally with 
the label facing front (toward the control 
panel). The side that indicates the toner 
color comes to the left.
Insert the cartridge into the printer, aligning 
the arrow on its left side with the arrow on 
the printer. 

7.

Firmly push in the toner cartridge until it 
stops, and rotate it. The 

 mark on the 

toner cartridge and the 

 mark on the 

printer align.

8.

Close the top cover by firmly pressing its 
center.

Important

• The top cover will not close unless the toner cartridge 

is installed correctly. In such case, reinstall the toner 
cartridge.

Summary of Contents for DocuPrint C3055 DX















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands