manualshive.com logo in svg

Fuji Xerox DocuPrint C3055 DX, User Manual

Share
Download
Fuji Xerox DocuPrint C3055 DX User Manual Download Page 141

6.3 Printing Problems

141

Printing takes too much time.

Is the [Graphics] tab > [Print Mode] on your print driver set to [High Quality]? Changing 
the [Print Mode] setting to [Standard] may improve print speed. 

Refer to

• Online help for the print driver

Printing may take time depending on the printing method for TrueType fonts. Change 
the printing method under the [Detailed Settings] tab > [Font Settings] on your print 
driver.

Refer to

• Online help for the print driver

When printing large data, or when it is taking too much time to print, enabling [Print 
Page Mode] on your print driver may improve print speed.
To use [Print Page Mode], additional memory must be installed to the printer.

Refer to

• Print Page Mode: Online help for the print driver

Image loss occurs in the upper 
portion of the page. 

Printing does not start from the 
desired position on the page.

Are the paper guides adjusted properly?
Slide the paper guides to the correct positions.

Refer to

• "4.2 Loading Paper" (P. 81)

Check whether the margins are set correctly on your print driver.

Refer to

• Online help for the print driver

Requested 2-sided printing, 
but the printer prints 1-sided.

The duplex unit may not be installed properly.
Check if the connector cable of the duplex unit is plugged correctly into the printer.

Symptom

Cause/Remedy

Summary of Contents for DocuPrint C3055 DX















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands