Foma SA800i, Manual

Page: 459 / 564

457
In
st
al
lin
g
co
mmun
icat
io
n
c
o
n
fi
gu
ra
tio
n
fil
es
Da
ta
co
mmu
nic
a
tio
n
Installing communication configuration files
Installing communication
configuration files
Install the communication configuration files to
establish data communication with FOMA terminal
and PC connected.
Installing SA800i communication
configuration files (drivers)
The procedure of installation on Windows XP is
described as an example.
• Install the files on Windows XP or Windows 2000
after logging on with the name having administrative
right. Installing with any other names results in an
error. For procedures to set administrative right of
PC, contact the PC manufacturer or Microsoft
Corporation.
• Before installation, make sure no other programs are
activated. Save and exit all active programs and
restart installation.
1
Insert the bundled CD-ROM into the CD-
ROM drive of PC.
2
Connect FOMA terminal to PC by using
FOMA USB connection cable.
"
新しいハードウェアの検出ウィザード
(Found
New Hardware Wizard)" screen is displayed.
•
Connection procedure
J
P456
• FOMA terminal has to be powered on when
connecting.
•
Select " いいえ、今回は接続しません。 (Not
connect for this time.)", and click " 次へ (Next)"
to install in Windows XP Service Pack 2.
•
Installing on Windows 2000
Following operations:
J
P457
•
Installing on Windows 98/Me
Following operations:
J
P457
3
Select " 一覧または特定の場所からインス
トールする（詳細） (Install from a list or
specific location (Advanced))" and click "
次へ
(Next)".
4
Select "
次の場所で最適のドライバを検索す
る
(Search for the best driver in these
locations)", uncheck " リムーバブル メディ
ア（フロッピー、 CD-ROM など）を検索
(Search removable media (floppy disk, CD-
ROM etc.))", and check "
次の場所を含める
(Include this location in the search)".
5
Click "
参照
(Browse)", specify the folder in
which the driver is saved, and click "OK".
• Folder is named as "<CD-ROM drive
name>:
=
USB Driver".
6
Click " 次へ (Next)".
7
Click " 完了 (Finish)" on the screen " 新しい
ハードウェアの検索ウィザードの完了
(Found New Hardware Wizard is finished)".
8
Continue to install 3 remaining
communication configuration files
referring to Step 3 to 7.
■
Under Windows 2000
a
After the connection is established (Step 2),
click "
次へ
(Next)" when the screen "
新しい
ハードウェアの検出ウィザード (Found New
Hardware Wizard)" is displayed.
b
Select "
デバイスに最適なドライバを検索す
る（推奨）
(Search for the best driver for the
device (recommended))" and click " 次へ
(Next)".
c
Check on " 場所を指定 (Specify the folder)"
and click "
次へ
(Next)".
d
Specify the folder and click "OK".
• Folder is named as "<CD-ROM drive
name>:
=
USB Driver".
e
Confirm the driver name and click " 次へ
(Next)".
f
Click "
完了
(Finish)".
• Install 3 remaining communication
configuration files.
■
Under Windows 98/Me
a
After the connection is established (Step 2),
click "
次へ
(Next)" when the screen "
新しい
ハードウェアの追加ウィザード (Add New
Hardware Wizard)" is displayed.
b
Select "
ドライバの場所を指定する
(Specify
driver location)" and click "
次へ
(Next)".
• For Windows 98, Select " 使用中のデバイスに
最適なドライバを検索する（推奨） (Search
the best drivers for the device in use
(recommended))" and click "
次へ (Next)".
See next page
DSC01_E.book 457 ページ ２００６年２月１４日 火曜日 午後１２時３１分