manualshive.com logo in svg

ExtremeSwitching 200 Series, Administration Manual

The Frigidaire 200 Series Use & Care Manual is your essential companion for efficiently operating and maintaining your Frigidaire appliances. This comprehensive manual covers all necessary instructions and tips to ensure optimal performance. Download this manual for free at manualshive.com, your reliable source for hassle-free manual downloads.

Share
Download
background image

Table 268: Interface Configuration Fields (continued)

Field

Description

IP Address

The IP address of the interface. This field can be configured only when the
selected IP Address Configuration Method is Manual. If the method is DHCP, the
interface attempts to lease an IP address from a DHCP server on the network,
and the IP address appears in this field (read-only) after it is acquired. If this field
is blank, the IP Address Configuration Method might be None, or the method
might be DHCP and the interface is unable to lease an address.

Subnet Mask

The IP subnet mask for the interface (also known as the network mask or
netmask). This field can be configured only when the selected IP Address
Configuration Method is Manual.

MAC Address

The burned-in physical address of the interface. The format is six two-digit
hexadecimal numbers separated by colons, for example 00:06:29:32:81:40.

IP MTU

The largest IP packet size the interface can transmit, in bytes. The IP Maximum
Transmission Unit (MTU) is the maximum frame size minus the length of the
Layer 2 header.

Bandwidth

The configured bandwidth on this interface. This setting communicates the
speed of the interface to higher-level protocols.

Encapsulation Type

The link layer encapsulation type for packets transmitted from the interface,
which can be either Ethernet or SNAP.

Forward Net Directed
Broadcasts

Determines how the interface handles network-directed broadcast packets. A
network-directed broadcast is a broadcast directed to a specific subnet. If this
option is selected, network directed broadcasts are forwarded. If this option is
clear, network directed broadcasts are dropped.

Proxy ARP

When this option is selected, proxy ARP is enabled, and the interface can
respond to an ARP request for a host other than itself. An interface can act as an
ARP proxy if it is aware of the destination and can route packets to the intended
host, which is on a different subnet than the host that sent the ARP request.

Local Proxy ARP

When this option is selected, local proxy ARP is enabled, and the interface can
respond to an ARP request for a host other than itself. Unlike proxy ARP, local
proxy ARP allows the interface to respond to ARP requests for a host that is on
the same subnet as the host that sent the ARP request. This feature is useful
when a host is not permitted to reply to an ARP request from another host in the
same subnet, for example when using the protected ports feature.

Destination Unreachables

When this option is selected, the interface is allowed to send 

ICMP

 Destination

Unreachable message to a host if the intended destination cannot be reached for
some reason. If this option is clear, the interface will not send ICMP Destination
Unreachable messages to inform the host about the error in reaching the
intended destination.

ICMP Redirects

When this option is selected, the interface is allowed to send ICMP Redirect
messages. The device sends an ICMP Redirect message on an interface only if
ICMP Redirects are enabled both globally and on the interface. An ICMP Redirect
message notifies a host when a better route to a particular destination is
available on the network segment.

Configuring Routing

ExtremeSwitching 200 Series: Administration Guide

263

Summary of Contents for 200 Series


















































































































































































































































































































































































Reviews:

No comments

Related manuals for 200 Series

Raritan SwitchMan USB-Combo SW2 Brochure preview
SwitchMan USB-Combo SW2
Brand: Raritan Pages: 2
Eaton Edison Cooper Power Series Installation And Operation Instructions Manual preview
Edison Cooper Power Series
Brand: Eaton Pages: 12
Kohler VERSO50 User Manual preview
VERSO50
Brand: Kohler Pages: 170
Homefibre OMS 113- 220 User Manual preview
OMS 113- 220
Brand: Homefibre Pages: 2
Lantech TGS-L6216XT User Manual preview
TGS-L6216XT
Brand: Lantech Pages: 24
Guntermann & Drunck UserCenter 2 Operating Instructions Manual preview
UserCenter 2
Brand: Guntermann & Drunck Pages: 20
Raisecom ISCOM2600G (A) Series Product Description preview
ISCOM2600G (A) Series
Brand: Raisecom Pages: 96
Black Box SW614A User Manual preview
SW614A
Brand: Black Box Pages: 57
rtd IDAN-LAN25255HR User Manual preview
IDAN-LAN25255HR
Brand: rtd Pages: 24
Lantech IGS-3208MGSFP User Manual preview
IGS-3208MGSFP
Brand: Lantech Pages: 27
Accton Technology 24/48 10/100 Ports + 2GE Management Manual preview
24/48 10/100 Ports + 2GE
Brand: Accton Technology Pages: 512
Rolls ABY32 Owner'S Manual preview
ABY32
Brand: Rolls Pages: 2
Broadcast Tools 38511 Installation Manual preview
38511
Brand: Broadcast Tools Pages: 10
Neol ePowerSwitch 1GR2 User Manual preview
ePowerSwitch 1GR2
Brand: Neol Pages: 47
TESmart CKS0301AIU User Manual preview
CKS0301AIU
Brand: TESmart Pages: 34
AVProEdge AC-AEX-RC-HUB User Manual preview
AC-AEX-RC-HUB
Brand: AVProEdge Pages: 31
ATEN CS-128A User Manual preview
CS-128A
Brand: ATEN Pages: 30
H3C A5500-24G Quick Start Manual preview
A5500-24G
Brand: H3C Pages: 8

Brands by name

Popular brands

Load more brands