Nodes 5-44
R
ADIO
P
AGER
R
ECEIVER
U
NIT
Description
The pager receiver unit is a digital radio receiver that displays and stores messages received from the pager transmitter unit.
The pager receiver must be turned on and is said to be in
standby mode
when the date and time are displayed. When a
message is received, it is displayed and the pager generates a call alert by either beeping or vibrating. The user can program
the unit to generate the desired call alert.
The unit can store up to 16 messages in its memory and the user can delete
all
messages or
individual
messages as
required. Each pager receiver unit has a unique 7 digit primary and 7 digit secondary address. This may be viewed and
entered as
Pager Address
in the
Radio PA Setup
menu
.
햲
Battery compartment
Note
Low Battery Alarm - If the units 1.5V “AAA” battery drops below a workable level, the pager will sound a low battery
alarm. The message “Change Battery” appears on the display along with the battery low symbol. Press any key to stop the
alert tone. Turn off the power of the pager and slide the battery compartment (1) cover off the unit. Insert the battery into
the battery compartment, ensuring that the polarity of the battery is correct. To protect the data you have stored in the pager,
do not leave the pager without a valid battery for more than a few minutes.
햳
Alphanumeric display
Note
Display Symbols - Various conditions are indicated by symbols on the bottom line of the display. These symbols are
described in the following table. Symbols relating to functions not specific to HUA operation (such as alarm clock) are
described in the pager manual supplied with the unit.
.
햴
Speaker
햵
Function buttons
1
2
3
4
Summary of Contents for 3GS
