Hardware Overview 2-6
B
EFORE
P
OWERING
U
P
●
Place the control panel in a dry and well ventilated location, as far as possible from any heat
sources.
●
Check for proper grounding. Un-charge your body by touching the Ground terminal.
●
Make sure polarity of detectors, keypads, and other devices are correct.
●
Connect AC power to initial Power Up (transformer only). Connect battery only after keypad
and sensors seem to be operating properly. (Do not power up with battery alone.) Verify power
polarity.
●
When the panel reaches you, it will be factory programmed. The settings in factory
programming represent the default settings of a standard installation (referred to as
Factory
Defaults
) and are used for testing purposes . It is advised that the engineer should be familiar
with all the features and options before attempting to program the system. For best results,
please read the manual before installation and programming.
●
Do not connect any devices to the battery terminals.
●
Never run wire zones alongside telephone wires, high voltage wires, or transmitting
antennae.
WARNING:
To prevent electrical shock, disengage the system power
and disconnect the telephone line before servicing this
unit.
Summary of Contents for 3GS
