DTM Print LX610e Color Label Printer Download Page 14

Page: 14 / 114

14 |

2A Label and Roll Specifications

Pre Die-Cut Labels.

A wide variety of pre die-cut label stock can be used in the printer. Refer to the

specifications and settings in the following sections before ordering custom stock from Primera or any
stock from another company.

Digital Die-Cut Labels.

If you are using the printer to digitally die-cut your own shapes and sizes only

DTM/Primera or Primera ASIA label stock can be used.

Important!

Test all custom made label stock with the intended printer before ordering large quantities!

Primera will only assume responsibility for custom label stock ordered from DTM/Primera or Primera ASIA.

Label Width

Gap Sensor Adjustment Range

Width of Opening

Distance from

edge of Media

to edge of Label

Label Height

Black Mark

Width

Label Sensing Methods

Method 1

: Label

Gap Sensing

Method 2

: Through-Hole

Sensing

Method 3

: Reflective/Black

Mark Sensing

(Black Mark must be printed
on back side of label stock)

Note: See table below for Max and Min values in inches and mm.

Gap Between

Labels

Section 2: Media, Cartridges and Knives

Summary of Contents for LX610e


















































































































Search results

Summary of Contents for LX610e

Reviews:

Related manuals for LX610e

Brands by name

Popular brands

DTM Print LX610e, Color Label Printer

Search results

Summary of Contents for LX610e

Reviews:

Related manuals for LX610e

Brands by name

Popular brands