DTM Print LX610e Color Label Printer Download Page 111

Page: 111 / 114

| 111

Place second paper towel on flat/hard surface.

b. Press the nozzles into the paper towel.
c.

Firmly tap the top of the cartridge three times to

force the ink out.

d. Wipe/Drag the cartridge in the direction indicated.
e.

Repeat until all colors are seen on the paper towel.

After wiping the nozzles, the paper towel should

show all three colors. If all three colors are present,

proceed to step 8. If the paper towel doesn’t show

all three colors, then repeat step 7. If paper towel

still doesn’t show all three colors repeating step 7,

then replace the cartridge.

8. Dry the cartridge.

Dry excess water from cartridge.

Ensure cartridge contacts are

completely dry. Printer damage

may result if cartridge contacts

are not completely dry.

9. Verify cartridge is now functioning properly by printing your label.

Summary of Contents for LX610e


















































































































Search results

Summary of Contents for LX610e

Reviews:

Related manuals for LX610e

Brands by name

Popular brands

DTM Print LX610e, Color Label Printer

Search results

Summary of Contents for LX610e

Reviews:

Related manuals for LX610e

Brands by name

Popular brands