DTM Print LX610e Color Label Printer Download Page 11

Page: 11 / 114

| 11

1D Identifying the Parts

These illustration shows the printer from various angles so all important parts can be identified.

Control Panel

Front Cover

The

Power LED

indicates that the printer is on and ready to receive print jobs.

The

Ink LED

will illuminate when a cartridge has 10% or less of its ink remaining.

The

Pause Button

is pressed to pause a job to allow for loading of label stock and ink cartridges. The print-

er pauses after the printing of the current label has finished.

The

Feed Button

is pressed in order to load label stock if the printer does not automatically detect the

stock. When stock is loaded each press of the button will cause one label or a few inches to be fed through
the printer.

The

Unload Button

is pressed to unload label stock after you receive an End of Roll message in PrintHub.

The printer will reverse the label stock through the feed area.

Summary of Contents for LX610e


















































































































Search results

Summary of Contents for LX610e

Reviews:

DTM Print LX610e, Color Label Printer, Page: 11 / 114

Search results

Summary of Contents for LX610e

Reviews: