manualshive.com logo in svg

Dini Argeo 3590 EBOX Series, Technical Manual

Share
Download
Dini Argeo 3590 EBOX Series Technical Manual Download Page 83

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator   E-AF03_05.01_14.07_EN_T.doc 

 

 

83 

6. NETWORK MANAGEMENT 

 

If in the indicator there is an ethernet board (SETHNET) it is possible to create a network between two or more instruments. 

If there are only two indicators the connection is made through a crossed Ethernet cable, while for the connection of more 
than two instruments it is necessary to use a switch/access point. In this last case, if there is an existing access point or 
cabled network, it is necessary to configure the network parameters of the modules before connecting them (see following 

section). 

All the SETHNET have this predefined address: 192.168.16.205.

 

 

6.1 INSTRUMENT NETWORK CONFIGURATION 

 
So that the instruments can comunicate through the SETHNET modules, it is necessary to configure the following 
parameters: 

-

 

BAUD RATE of the COM.AUX a 115200 (step 

SEtuP

 >> 

SEriAL

 >> 

CoM.AuX   

>> 

bAud >> 115200

)

 

-

 

Enable the ETHERNET protocol on the COM.AUX ( step 

SEtuP

 >> 

SEriAL

 >> 

CoM.AuX   

>> 

ProtoC 

>>

 Eth.nEt

). 

This protocol require the configuration of the following parameters:

 

1.

 

nodE.Gr 

NODE GROUP

 

2.

 

nodE.id 

NODE ID

 

3.

 

iP.ModE

 

TYPE OF IP (STATIC or DYNAMIC) 

4.

 

iP.Addr 

IP ADDRESS 

5.

 

nEt.MSK 

SUBNET MASK             

6.

 

Auto.db 

AUTOMATIC DB ALIGNEMENT(If enabled, it enables the automatic synchronization of the      

databases)  

7.

 

n.nAME 

NETWORK NAME 

 

Example: network between two instruments with static address.

 

 

 
EXAMPLE 1 

GROUP

 1

 

ID

 1  

IP  ADDRESS                                

192 . 168 .  16  . 2 

SUBNET MASK

          255 . 255 . 255 . 0 

 
GROUP

 1 

ID

 2  

IP  ADDRESS         

            192 . 168 .  16  . 7 

SUBNET MASK                   

255 . 255 . 255 . 0 

 

EXAMPLE 2 

GROUP

 2

 

ID

 1  

IP  ADDRESS                          

192 . 168 .  35  . 2 

SUBNET MASK

          255 . 255 . 255 . 0 

 

GROUP

 2 

ID

 2  

IP  ADDRESS         

            192 . 168 . 35 . 7 

SUBNET MASK                   

255 . 255 . 255 . 0 

 

 
 

 

 

 

 

Summary of Contents for 3590 EBOX Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands