Dini Argeo 3590 EBOX Series Technical Manual Download Page 27

Page: 27 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

309

Select A+B visualization

310

Format Linking to the Input Weigh Printout (FM.IN)

311

Format Linking to the Output Weigh Printout(FM.OUT)

312

Format Linking to the Single Weigh Printout (FM.SING)

313

Customer alpha-betic search (ALP.CUS)

314

Material alpha-betic search (ALP.MAt)

315

Vehicle alpha-betic search (ALP.VEh)

316

Change Of The Second Line Visualization In A+B Mode

(DISP.CH)

317

Network state (nEt.StA)

318

Network monitor (nEt.Mon)

319

Archives alignment (db.ALiG)

320

Unlock weighing list records (unLoCK)

321

Connect network (n.StArt)

322

Disconnect network (n.StoP)

323

Send remote key (rEM.KEY)

324

Send remote long key (r.KEY.L)

325

Remote scale change (rEM.CGH)

VISUALIZATION / PRINTOUT MENU

400

Number of Ticket Copies (CoPiES)

401

Set progressive digits (Prg.1)

402

Set progressive label (Prg.2)

403

Automatic Lot Resetting (0.Prg)

404

Display Customer Total (V.t.Cus)

405

Print Customer Total (Prn.Cus)

406

Reset Customer Total (0.Cus)

407

Reset all Customer Totals (0.CusS)

408

Display Material Total (V.t.Mat)

409

Print Material Total (Prn.Mat)

410

Reset Material Total (0.Mat)

411

Reset all Material Totals (0.MatS)

412

Display Vehicle Total (V.t.VEh)

413

Print Vehicle Total (Prn.VEh)

414

Reset Vehicle Total (0.VEh)

415

Reset all Vehicle Totals (0.VEhS)

416

Display Partial Total (V.t-0)

417

Print Partial Total (Prn.t-0)

418

Reset Partial Total (0.t-0)

419

Display General Total (V.t-1)

420

Print General Total (Prn.t-1)

421

Reset General Total (0.t-1)

422

Display Grand Total (V.t-2)

423

Print Grand Total (Prn.t-2)

424

Reset Grand Total (0.t-2)

425

Reset Scale Totals (0.t-ALL)

426

Reset Weighs List (0.W.LIST)

427

Alibi Memory Reading (ALIBI)

428

Printout and Reset Customer Total (Prn.0.CuS)

2ndF + F1

429

Printout and Reset Material Total (Pr.0.Mat)

2ndF + F2

430

Printout and Reset Vehicle Total (Pr.0.VEh)

2ndF + F2

431

Progressive edit (Pr.Edit)

432

Change the views from KG to Lb and vice-versa

WEIGHING THRESHOLDS

500

Set maximum threshold (tr.HI)

501

Set minimum threshold (tr.LO)

Summary of Contents for 3590 EBOX Series





































































































































Search results

Summary of Contents for 3590 EBOX Series

Reviews:

Brands by name

Popular brands

Dini Argeo 3590 EBOX Series, Technical Manual

Search results

Summary of Contents for 3590 EBOX Series

Reviews:

Brands by name

Popular brands