manualshive.com logo in svg

Dini Argeo 3590 EBOX Series, Technical Manual

Share
Download
Dini Argeo 3590 EBOX Series Technical Manual Download Page 34

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator   E-AF03_05.01_14.07_EN_T.doc 

 

 

34 

See section 6 (

USER MAN.REF.

) for details on the functioning. 

 

(*) 

with approved instrument: 

- by confirming the setting of ENABLED or CYCLIC it is possible to modify the clearing percentage b/-1 

and +/-10 %. 

 

(!) ENABLED, +/-10 %   

 

(*) << 0.PErC >>

   ZERO FUNCTIONS IN WEIGHING PHASE 

Acquisition of the gross zero through the ZERO key. 

 

 

 

   

 

 

 

Set the clearing percentage in relation to the capacity (in b/-1 and +/- 50 %). 
By entering the 0 value, it’s possible to disable the ZERO functions in the weighing phase. 

 
See section 6 

(USER MAN.REF.)

 for functioning details. 

 

(*)

 In case of approved instrument, the settable values are between 0 and 2. 

(!) +/-2 % 
 

(*) << 0.trACk >> 

ZERO TRACKING

 

This menu allows setting the zero tracking, in other words, the compensation parameter of the scale’s thermal drift; 
the set value corresponds to the number of divisions that is reset in the fixed time of 1 second:

 

TR. ½

  +/- half division. 

TR. ¼ 

+/- one fourth of a division.

 

TR. 1

  +/- one division. 

TR. 2

  +/- two divisions. 

TR. no

  tracking disabled. 

(!) TR. ½ 
(*) 

with APPROVED instrument it is possible to select just the 

TR. no

, 

TR. ½ 

,

 TR. ¼ 

parameters.

 

 

(*) << diV.Stb >>  

DIVISIONS BY STABILITY 

In this step one enters the number of divisions by which the instrument detects the weight stability; the higher the 
number  of  divisions,  less  is  the  sensitivity,  and  consequently  the  stability  is  more  easily  detected.  The  possible 
values are 0…99. By setting the 0 value, the check is disabled. 

(!) 02

 

(*) 

with APPROVED instrument, the parameter is read-only. 

 

<< GrAV >>  

GRAVITY ZONE AND ZONE OF USE 

In this step one selects the gravitational acceleration value 

of calibration and of use

 of the instrument: 

Manual entry of the g value: the instrument is ready for the manual entry of the gravitational acceleration value. 
If one enters a wrong g value: the minimum decimal value is proposed (9,75001); by a wrong g value one intends a 

decimal number not including between 9,75001 and 9,84999 (included). 

(!) g = 9,80655 
(*) 

with APPROVED instrument the parameter is read only. 

 

(*) << CALib.>>   

SCALE CALIBRATION 

See section “3.3 SCALE CALIBRATION”. 

(*)

 with APPROVED instrument the parameters inside of this step are read only. 

 

(*) << 0.CALib. >>  

CALIBRATION OF ZERO 

See section “3.3 SCALE CALIBRATION”. 

(*) 

In case of approved instrument the parameter is not displayed.

 

Clearing percentage 
(blinking) 

 

0.PErC 

02 

Summary of Contents for 3590 EBOX Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands