Dini Argeo 3590 EBOX Series Technical Manual Download Page 48

Page: 48 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

<< ini.AL >>

INITIALIZES ALIBI MEMORY (*)

The initialisation cancels all the data stored in the Alibi memory; by pressing

ENTER

one is asked to confirm the

operation. The display shows

SURE?

; press

ENTER

again to confirm or another key to cancel.

At the end the "oK" message appears if the operation is made with success; otherwise the "Err" message is displayed

NOTE

: It is not possible to make the initialisation on an approved instrument

(*)

In case of approved instrument the parameter is not accessible

<< dSALE >>

DIRECT SALE (*)

limitations disabled

YES

limitations enabled

Refer to the user manual for the functioning description

(USER MAN.REF.).

(!) NO

(*)

In case of approved instrument the parameter is not accessible.

<< PC.KEYb >>

PC KEYBOARD CONFIGURATION

<< KEY.uSE >>

USE OF PC KEYBOARD INPUT

Normal

Use of the external PC keyboard (see in the user manual section 4.1.5).

READER

Enabling data reception from external reader (See relative manual)

(!) Normal

<< LAYout >>

EXTERNAL PC KEYBOARD LANGUAGE

ENGLISH

American / English

DEUTSCH

German

FRANCAIS

French

ITALIANO

Italian

ELLENIKA

Greek

(!) ENGLISH

<< diAG. >>

DIAGNOSTICS MENU

It’s a submenu inside of which it is possible to check the software and hardware components of the scale, accessible also
during the weighing, keeping the

key pressed at length.

<< PrG.UEr >>

FIRMWARE

Software version check.

<< WEiGht >>

WEGHT

By pressing

ENTER

the display shows:

If various scales are connected independently by pressing the F6 / F7 keys it is possible to select the scale to be
checked.

By pressing F5, it is possible to test the minimum value, present value and maximum value of the weight.

converter points per division
(A)=Analogue (D)=Digital
data per second of the converter

Checked scale

WEIGHT dv(106)

0.049 (A) 020

Summary of Contents for 3590 EBOX Series





































































































































Search results

Summary of Contents for 3590 EBOX Series

Reviews:

Brands by name

Popular brands

Dini Argeo 3590 EBOX Series, Technical Manual

Search results

Summary of Contents for 3590 EBOX Series

Reviews:

Brands by name

Popular brands