manualshive.com logo in svg

Dini Argeo 3590 EBOX Series, Technical Manual

Share
Download
Dini Argeo 3590 EBOX Series Technical Manual Download Page 40

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator   E-AF03_05.01_14.07_EN_T.doc 

 

 

40 

(!)  001

 

 

<< dECiM.>>  

REMOTE SCALE’S DECIMALS

 

Enter the number of scale decimals (from 0 to 5). 

(!)  0 

 

<< u.M. >> 

REMOTE SCALE’S UNIT OF MEASURE

 

Select the unit of measure of the scale from those suggested: G, KG, t, Lb. 

(!) – G – 

The two following parameters allow generating the stability of the weight communicated by the remote scale and 
allow managing the stability indicator on the indicator: 

 

<< StAb. >>  

NUMBER OF READINGS PER STABILITY

 

Enter the number of consecutive readings which the indicator must take into consider in order to obtain stability 

(max 2 characters, from 01 to 20). 
By setting 

00 

is possible the choosing between “INSTAB. STRING “, “STAB. STRING” and “IGNORE STABILITY”. 

-  by  pressing 

ENTER 

on  “INSTAB.  STRING”  OR  “STAB.  STRING”

 

it’s  possible  to  enable  the  reading  of  the 

instability/stability in the string transmitted from the remote scale; one sets in sequence: 
1) the position of the instability/stability indication, in the string transmitted from the remote scale, knowing that the 
first character on the left of the string has the position 00;

 

it’s possible to set up to 3 characters (from 000 to 100); 

by setting 255, the reading of the instability/stability is disabled and the weight is considered as stable. 
2) the instability string, in other words, the characters transmitted from the remote scale when the weight is unstable 
(up to 3 characters): 
If  the  value  in  the  instability  indication  corresponds  to  the  set  value,  the  weight  is  considered  to  be  unstable; 

otherwise, it is considered as stable. 

 

By pressing 

C

 the instability check is disabled and the weight is considered to be always stable. 

 

(!)  03

 

 

<< StA.int >>  

WEIGHT DIFFERENCE PER STABILITY

 

Enter the maximum value (2 characters, from 0 to 20) which can be taken on by the difference between the weights 
of consecutive readings which are set in the preceding step. 

If the weight difference between the tested readings is equal or less than the set value, the weight is considered 
stable (stability indicator off), otherwise the weight is considered unstable (stability indicator on).  

(!)  02 

 

<< round.S

 

>>

   ROUNDING

 

ENABLED

  

 

 

DISABLED

  

 

(!) DISABLED 

 

 

EXAMPLE:  

WEIGHT SENT BY REMOTE SCALE 

“   41.6375 g G     0.5006 g  T” 

 

If the parameters are enabled, the displayed weight will be “41.638”.  

       

If the parameters are disabled the displayed weight will be “41.637”.  

       

 

NOTE

: if the function is enable is also necessary to set the correct number of decimals (considering that the 

rounding eliminate the last digit). 

 

 
 

 
 
 

 
 

Summary of Contents for 3590 EBOX Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands